To remove Schlage lock cylinder without key, follow these steps:

  1. Step 1: Remove the escutcheon plates by using a screwdriver.
  2. Step 2: Remove the screws that hold the lock.
  3. Step 3: Insert the straightened paper clip into the lock and turn it to a 12 o’clock position.
  4. Step 4: Take the lock cylinder out.

How do you remove an old Schlage Lock?

Quote from the video:
Quote from Youtube video: We're going to turn the knob clockwise. Just a little bit we're going to put some pressure and push down on the tab. You'll feel that it has released.

How do you remove a Schlage Lock with faceplate?





You can use a flathead screwdriver to pop the rectangular faceplate off, then attach the round drive-in faceplate by sliding it over the top of the bolt and snapping it into place.

How do you remove a Schlage keypad?

Quote from the video:
Quote from Youtube video: Next remove the outside thumb turn and lift out the cylinder. Set the rest of the keypad assembly aside for reinstallation. Now use a small flat-head screwdriver to remove the block.

How do you remove a Schlage lock cylinder without a key?

Quote from the video:
Quote from Youtube video: But if you go and pick up a handle or a doorknob from like restore or something like that go ahead and do this.

How do you remove old Schlage door knobs?

Turn the knob all the way and hold it there, insert a small stiff object into the collar hole to depress the knob retention tab while pulling outward on the knob. It will slide off into your hand.

How do you take apart a Schlage door handle?





How to Remove Schlage Lock Lever Handles

  1. Insert the key in the handle on the outside of the door. …
  2. Insert the pin tool — or a 6d finish nail — in the hole at the other end of the handle barrel. …
  3. Pull the handle off.

How do you remove a Schlage keyless deadbolt?

Quote from the video:
Quote from Youtube video: Go to the back of the exterior keypad assembly using the flathead screwdriver remove the cylinder compartment. Cover using a magnetic head screwdriver remove the screw holding the cylinder in place.

How do you remove a Schlage door lever?

How to change the handing of your Schlage door lever

  1. Locate the pin tool that came with your lock.
  2. Insert the tool into the small hole on the lever base and gently depress the retainer pin while pulling the lever away.
  3. Remove and exchange both levers.

How do you disassemble a lock cylinder?

To change an interchangeable lock cylinder, remove the flat screw, turn the key slightly to the right, remove the cylinder, and, turning the key back to the left, place the new cylinder.

Can you rekey a Schlage lock without the original key?



Re-keying a Schlage without a key is difficult because the locks were purposely designed not to be easy. A locksmith could do this quickly, but may be expensive since they will need to do a house call without a key. New Schlage locks come with a reset key that allows you to re-key the lock without other existing keys.

How do you open a Schlage Lock with a dead battery?

How do you unlock a Schlage Control lock that has a dead battery?

  1. Touch a new high-quality alkaline 9-volt battery to the contacts below the bolt throw. …
  2. Wait for 1 red light and then 3 green lights with 3 beeps. …
  3. Present a valid credential.
  4. Rotate the bolt throw away from the door edge.
  5. Replace the batteries.

What happens if Schlage Lock battery dies?

Simply use the thumbturn to lock and unlock the door from the inside. Will the lock still work if the power goes out? Yes. All Schlage electronic locks are battery operated, so they will continue to work during a power outage.

How do you open a Schlage door lock?



To unlock the door using the keypad, enter your four- digit user code. When you see the Schlage button turn green, rotate the thumbturn toward the door’s hinges. If the Schlage button turns red, you have entered an incorrect user code. If it does not light up at all, you may have entered too many incorrect codes.

What kind of battery does a Schlage Lock take?

AA alkaline batteries

The Schlage Connectâ„¢ Smart Deadbolt requires four new AA alkaline batteries, installed on the interior side of the lock. Remove the black battery cover on the interior side of the lock by sliding it up. Unsnap the battery connector (a short wire), remove the battery tray and replace the batteries.

How long do batteries last in Schlage locks?

Schlage Connect Smart Deadbolt (BE469ZP)



The Schlage Connect Smart Lock uses 4 AA alkaline batteries, expected to last up to two years. Plus, the lock features a low battery warning that will alert you before the battery drains completely. The lock uses Z-wave as its communication protocol.

How do I change the battery in my door lock?



From the inside part of your door, slide the cover up and off of your door lock. Grip the battery pack from the top and pull it up and out. Remove the old batteries and replace with four AA alkaline batteries Replace the battery pack and the cover on your door lock Remember to safely dispose of the old batteries.

Why is my Schlage Lock not working after battery change?

For the most part, your Schlage keypad lock may stop working if the batteries are low or completely drained. If your lock suddenly stops working, the first thing to do is replace the batteries and then try to operate it again. Also, check if the battery connector is disconnected and get it properly connected.

Why does my Schlage Lock blink orange?

Orange flashes indicates lock is in the middle of a programming sequence.