Should deck boards go under siding?

Keep in mind the bottom of the upper siding should be at least two inches above the flashing or the decking that’s near the house. Never put horizontal siding in direct contact with any horizontal material.

How do you start siding over a deck?






Quote from Youtube video: But you want to make sure you line the siding up with each other so in order to do that the best thing to do is take a speed square.

How do you remove vinyl siding from a ledger deck?

Aluminum and vinyl siding can easily be removed with tin snips from an area one foot surrounding the ledger board location. You can then trim the pieces to be reinstalled with a J channel after the deck is completed for a clean, finished look. Wood or concrete siding will have to be cut away using a circular saw.

Can you attach a deck over siding?

Attach-A-Deck works great for mounting a ledger over existing siding. You just drill 2 1/2 in. holes through the siding to the face of the sheathing, apply the Attach-A-Deck fasteners and mount the ledger to the house.

How do you flash a deck against siding?

Quote from the video:
Quote from Youtube video: You need to have a certain distance between the siding and the finished piece of decking that could be a half inch it could be up to two inches depending on the branded type of siding.

How do you flash between deck and house?





Quote from the video:
Quote from Youtube video: So let's go over some of the components of this little demo here of the deck ledger flashing. And then we'll talk about the flashing. Itself. So this is the port concrete foundation on some grass.

How do you replace a piece of siding?

Quote from the video:
Quote from Youtube video: If they don't overlap when you put them together tight when it shrinks you'll have an opening. All right now all we have to do now is take the piece start here on an angle and push it up.

How do you install vinyl siding over wood?

Here’s how to install vinyl siding over wood siding:

  1. Inspect the Wood Siding for Severe Damage. …
  2. Flatten Surface with Furring and Foam. …
  3. Secure the Base with a Moisture Barrier. …
  4. Modify All Openings. …
  5. Install the Starter Strip, J-Channel, and Undersill Trim. …
  6. Start Installing the Panels.


How do you install new siding over old siding?



There are two options for this: Remove the siding and install Oriented Strand Board (commonly referred to as OSB), or to use the existing siding that’s on the house now as substrate (or layer beneath the top surface) underneath the HardiePlank siding.

How should a deck attached to the house?

The deck ledger is the deck floor rim board attached to the house, and it should be positively connected to the floor structure of the main building with bolts or lag screws, not nails.

What is deck skirting?

Skirting a deck. A beautifully built deck can be enhanced by a single feature that will add appeal and function by enclosing the underside of a deck with decking material or custom screening. This particular detail is called skirting.

How do you replace a ledger board on an existing deck?



Quote from the video:
Quote from Youtube video: We banged our top plate up jacked it up about an inch to an inch and a half got. Everything level. And then just came in with some two by six Mesa.

Is flashing required on a deck?

Flashing is required where exterior porches, decks, or stairs attach to a wall or floor assembly of wood frame construction.

Can you put flashing over pressure treated wood?

Never use galvanized steel or aluminum flashing in contact with an ACQ pressure-treated wood ledger board because it will corrode. Vinyl flashing is the least expensive option, but it may not work as well in areas with extreme temperature fluctuations.

How do you install drip flashing on a deck?

Quote from the video:
Quote from Youtube video: First. We have the top hand flashing on which is going to go just above the ledger board this is going to allow.

What is a deck ledger?



The deck ledger is the deck floor rim board attached to the house, and it should be positively connected to the floor structure of the main building with bolts or lag screws, not nails. The main objective of this article is to alert property owners and code officials to decks with “nailed-only” deck ledger connections.

How far should deck boards be from siding?

Either use two stainless steel screws through the face of the board at each joist or ExoDek QuickClips to fasten the boards to the deck frame. The first board you install should be about 1/8″ (3.5mm) away from the siding, to account for drainage, expansion and contraction.

How do you attach a ledger board to a house for a patio cover?

Quote from the video:
Quote from Youtube video: For like screws or another alternative through bolts with accompanying nuts at the ledger. Board. In a suitable flashing. Usually a metal L flashing. To protect against moisture seepage.

How do you install Ledger spacers on a deck?

Quote from the video:
Quote from Youtube video: Remove the ledger Center the spacers over the holes. And screw them to the ledger. Apply sealant in and around the bolt holes to help prevent moisture intrusion now secure the ledger with the bolts.

What is a deck ledger spacer?



Deck2wall® Spacers (D2W) are polypropylene spacers designed to be installed between a deck and house. This allows water and debris to flow between the ledger and the house, promotes circulation and drying, and helps prevent rot.

How do you replace a ledger board on an existing deck?

Quote from the video:
Quote from Youtube video: We banged our top plate up jacked it up about an inch to an inch and a half got. Everything level. And then just came in with some two by six Mesa.

How many lag bolts do you put in a ledger board?

Approved Fasteners



The International Residential Code lists two fasteners for directly attaching ledgers to a house: 1/2-inch-diameter hot-dip-galvanized hex-head machine bolts and 1/2-inch-diameter hot-dip-galvanized lag screws.

Do you use washers with lag screws?

Another important consideration when fastening with a bolt (regardless of whether it is a through-bolt or lag bolt) is the use of washers. A washer adds to the bolts area of holding power. The bigger the washer the better the holding power.

Can I use 2×6 for ledger board?

Trex recommends 16″ OC at most, 12″ if running the boards diagonally. This is fine for 2×6 spacing. For the ledger, it’s worth replacing so it’s the same size. You might not be able to fully secure the larger hangers to the smaller ledger.