How do you replace siding on a gas line?
Quote from the video:
Quote from Youtube video: Add some silicon caulk to waterproof the hole. When siding around a water spigot. Cut a notch around the spigot that leads a quarter inch gap around the entire fixture.
How do you cut vinyl siding around pipes?
Quote from the video:
Quote from Youtube video: Slide it in pipe uh fl when you flap it sideways you could it's easier to put in. And there you have it you see that is a nice cut. I can put caulk in here. Or you can tape it from the back.
How do you install siding around an electric meter?
Quote from the video:
Quote from Youtube video: The back wall. You would definitely have to cut power to this meter base remove. It from the wall. Then pull out your old piece of wood replace. Your new piece of wood. Do.
How do you cut back vinyl siding?
For vinyl shake siding, you can cut panels using snips or a circular saw with a blade that can be used for vinyl. Snips work best for long, vertical cuts while circular vinyl siding saws work best for short, vertical cuts.
How do you cut vinyl siding already installed?
A rotary tool is the best tool for cutting siding that is already hanging. You can also make curved cuts with a rotary tool fitted with a mini saw blade or a zip tool, which is a cutting bit that looks like a drill bit.
How do you install siding around a water faucet?
If the faucet falls in the center of the siding then cut the siding in half and notch each half to fit the faucet. Slide the siding up behind the faucet and nail in place. If the siding was cut in half to accommodate a faucet that fell in the center then slide the pieces in from the sides and nail in place.
What is utility trim for vinyl siding?
Utility Trim: a piece of trim used any time the top lock has been removed from the siding, to secure a siding panel. Also referred to as “undersill” or “finish” trim; double utility trim is also available.
Can you use a chop saw to cut vinyl siding?
These include miter saws, chop saws, table saws and handheld circular saws. Mark the area to cut and slowly feed the blade into the siding. The backward rotation of the saw blade not only cuts the vinyl, but melts the edges to make a very smooth and jagged-edge free cut.
Why do you need to leave a ¼ expansion joint when installing vinyl siding?
Allow for Expansion and Contraction
Vinyl siding installation must allow for material expansion and contraction caused by weather. Cut your siding in lengths with a 1/4-inch gap for expansion wherever siding butts accessories.
What nails should I use for vinyl siding?
Use aluminum, galvanized steel, or other corrosion-resistant nails, staples, or screws when installing vinyl siding. Aluminum trim pieces require aluminum or stainless steel fasteners. All fasteners must be able to penetrate a minimum of 1 1/4” (32mm) into nailable material, such as wood sheathing and framing (Fig.
Can I use screws for vinyl siding?
A stainless steel screw is the very best, but also the most expensive. Vinyl coated screws are great too. In most cases you can purchase these in rather small quantities. No matter which screw you buy, make sure it is a Phillips head screw because they are the easiest to use.
Can you use a nail gun on vinyl siding?
Vinyl siding can either be nailed by hand—with a hammer—or by a power nailer.
How far apart should vinyl siding be nailed?
Vinyl siding that’s nailed on too tight doesn’t leave room for the materials to expand and contract, and that causes ripples to form come summertime. For the best results, leave at least 1/16 inch between the nail head and the siding to give it some room to grow.
Can you nail in loose siding?
Use the siding removal tool to gently expose the nail hem that needs new nails. Purchase galvanized steel or aluminum roofing nails with a head at least 3/8 inch in size. Drive new nails into the center of the slots on the siding nail hem.
Do you nail vinyl siding starter strip tight?
galvanized roofing nails for your vinyl siding unless the sheathing has foam on it. Then you’ll want longer ones. Don’t drive the nails tight: Each panel should be able to move back and forth or the siding will bubble on really hot days.
Does vinyl siding need strapping?
Furring or strapping must be applied to create an even base for siding.
What should go under siding?
Underlayment
Underlayment or weather resistive barrier (WRB) is installed between the siding and the sheathing. This can be tar paper or a house wrap such as HardieWrap® or Tyvek HomeWrap®. HardieWrap® is great for keeping water out and at the same time letting water vapor escape from the house.
Should I use furring strips for siding?
Most panel siding requires a solid surface or backing for a secure and stable attachment. Furring strips provide reliable backing. The second — and most important — purpose of furring strips for siding is that they create a crucial gap between the siding and the weather-resistant barrier of the home’s exterior.
