How do you remove a P-trap without a wrench?
Unscrew the nuts holding a plastic P-trap by hand, gripping the trap firmly with one hand and rotating each nut counterclockwise. You must unscrew two nuts to remove the trap. One holds the trap to the tailpiece, the small length of pipe extending down from the sink, and the other holds the trap to the drain line.
How do you remove a pedestal sink p-trap?
Quote from the video:
Quote from Youtube video: And there's two nuts. Then the only nut that I can really gain access to is this one which sits at the very back of the pedestal. I can just barely get a wrench in there to loosen. It.
How do you unscrew a U bend?
Grab a bucket or a large bowl and place it under the U-bend before carefully unscrewing the threaded caps on either end of the bent length of pipe. These should come undone easily unless the plumbing hasn’t been serviced in a while; if they’re sticking, add a little bit of lubricant to help them pull apart more easily.
How do I remove glued PVC pipe?
Quote from the video:
Quote from Youtube video: When you found the right one heat it thoroughly for around one minute and put it inside the pipe as such. What this does is it heats up the glue just enough for the pipe to unstick.
How do you loosen a stuck pipe fitting?
Quote from the video:
Quote from Youtube video: Fitting use a regular propane or map gas torch to get it nice and hot. And then take the joint apart while it's still heated. That will make it a lot easier since the fitting expands.
Where is the P-trap on a pedestal sink?
Sit on the floor to the side of the pedestal, near the wall, to view the now-visible P-trap. Loosen by hand, if possible, the slip-nut at the top of the P-trap where it meets the tailpipe of the sink’s pop-up drain by twisting it counterclockwise.
How do you remove the base from a pedestal sink?
Quote from the video:
Quote from Youtube video: You'll want to go ahead and take your sharp razor knife and cut an incision around the floor. Once you cut that incision on the caulk around the floor.
How do you access a sink trap?
Quote from the video:
Quote from Youtube video: Slide it off dump the water in. There. Loosen up these nuts now loosen. Them up all the way. And you can leave them right on the pipes. And then you can pull this down dump out a little water.
How do you loosen a stuck PVC P trap?
Quote from the video:
Quote from Youtube video: So you want to grip it just enough that you have a hold on it. Then I take my pair of pliers. And I'll grip the other one and just give it a little twist. And they should come right apart.
How do you remove a PVC P trap glue?
Quote from the video:
Quote from Youtube video: And you just let it sit in there and what happens is is that the pipe actually heats up and becomes malleable almost becomes rubber like. And you're able to pry. It out.
Will a heat gun loosen PVC glue?
Quote from the video:
Quote from Youtube video: Below I think this baby is once he got like 1500 watts probably puts out like about you know two million degrees or something get a user to heat up the joints of the PVC.
Is melting PVC toxic?
When burned PVC produces carbon monoxide, dioxins, and chlorinated furans. Dioxins and furans are two of the most toxic man-made products because the lowest amount of either product can cause diseases such as, cancer and birth defects.
How do you heat PVC pipe without a heat gun?
Quote from the video:
Quote from Youtube video: Or you can just grill it outside I'm using a skillet here and just my cooktop. I know some people even use a torch to heat the sand up.
How do you Unglue a PVC pipe with a heat gun?
A heat gun is like a high-powered hairdryer, and it’s often used for removing paint or loosening metal pipes. Start with the heat gun on a lower setting and begin to heat up the PVC pipe. As the pipe heats up, work on the pipe with the pliers by twisting it away from the other pipe. It’s a slow process, so be patient.
How do you soften pipe cement?
Quote from the video:
Quote from Youtube video: I think the flame actually burns some of that off. It's already starting to soften. Right around soften up right around the edges. So this method seems to be.
What can dissolve PVC?
Cyanoacrylate and acrylic [PMMA, MMA, etc] based polymers can get good bonding at the molecular level. [ABS, PVC, HIPS] => Acetone and Methyl Ethyl Ketone [MEK aka 2-Butanone] will dissolve both ABS and PVC and chemically rebuild the joint in a less ordered manner as the solvents dries.
