How do you extend a sink drain to a P-trap?
Quote from the video:
Quote from Youtube video: So you need the proper washer insert the retention nut. And the nylon washer. And loosen up there p-trap. And install the extension tail piece. And stole another retention nut.
How do you connect a P-trap to a sink tailpiece?
Quote from the video:
Quote from Youtube video: Take your straight pipe. Put it up here. So lightly tighten it down like that again take your nut. And then put on. Now take your p-trap.
What is a trap adapter?
PVC Threaded Trap Adapter to connect your sink drainage to the drain pipe that extends through the wall or floor. Designed to fit most tubular drain applications, this universal adapter is constructed from PVC plastic.
How do you connect a pipe to a kitchen sink drain?
Quote from the video:
Quote from Youtube video: Now at a washer making sure the taper is toward the end then fit into the marble connector loosely without tightening the nut. Next attach the p-trap to the trap arm loosely thread these connections.
Can P trap be lower than drain pipe?
You attach the p-trap directly to the drainage and manuever the p-traps exits into you existing drain. It is not ideal to have the p-trap below the the exit drain because water gravity has to force the water out instead of it flowing downwards naturally. They both work and have seen it many times.
How do you offset a P trap?
Quote from the video:
Quote from Youtube video: You need quarter inch slope per foot on an inch and half drain. Pipe now again align the p-trap with the 45. And measure the piece that will go between.
How do you install a P-trap adapter?
Quote from the video:
Quote from Youtube video: Apply it to the trap adapter. And to the drain. Line. Now you push as far as possible. And hold it for 10-15 seconds. Now you can release it and this is how you install trap adapter for the climax.
What is the name of the fitting that connects the P-trap to the drain?
Tailpiece: Often referred to as the drain tailpiece, this is the section of piping that connects to the drain fitting.
How do you make a P-trap?
Quote from the video:
Quote from Youtube video: And the sinks tail piece this creates the straight line needed for a correct installation. The next pipe to be installed is our adapter tee which allows us to attach both drains to the same p-trap.
What if new kitchen sink drain doesn’t line up with existing pipes?
In general, if the P-trap doesn’t line up with the drain, you can adjust the length and height of your drainpipes by cutting them or simply slipping them in and out of their fittings.
How do you install a P-trap under a kitchen sink?
Quote from the video:
Quote from Youtube video: To begin measure and cut the wall tube to the length required. Next position the nuts and washer on the wall tube insert wall tube into waste connector and tighten the existing nut.
How do you connect metal pipes under sink?
Quote from the video:
Quote from Youtube video: This right here is the key to hooking it up going through the wall. This is a flexible pipe. That we can hook up straight to our line right here. So we'll take it and tighten it down to our. Line.
How do I lower my kitchen sink drain pipe?
Quote from the video:
Quote from Youtube video: This i'll show you okay the first step is you have to cut off the main water. And then you have to disassemble the plumbing. And then we can pull out the base cabinet.
How far should the sink drain pipe go into the P-trap?
Maximum Distance
However, the Universal Plumbing Code stipulates that the total developed length of all tailpieces, arms and fittings connecting the drain to the p-trap must be 24 inches or less.
How far can the P-trap be from the drain?
What is the minimum and maximum distance a P-trap can be below a sink? There is no minimum distance specified by the building code, but the maximum is 24” per International Residential Code (IRC) and Residential Edition of Florida Building Code (FBC 1002.1), measured from fixture outlet to trap weir.
Does every P-trap need a vent?
P-traps need vents
1 – They give the sewer gases a place to vent, so they do not build pressure inside your sewer lines.
What size of P-trap is required for a kitchen sink?
1 ½ inches
Bathroom sink P-traps are typically 1 ¼ inches in diameter and kitchen sink P-traps are typically 1 ½ inches in diameter.
Does it matter which way the P-trap goes?
In a Shower P-Trap, Can the Lower Curvature Be Backward? When you cement it together, the straighter side of the trap- which is not as curved- should be what the 90 degree piece is glued onto. Then the curved end should be connected to the shower drain. However, gluing the P-trap shouldn’t affect the drainage.
How should P-trap look?
Quote from the video:
Quote from Youtube video: If you notice a lot of extra piping under your sink then you're looking at the p-trap. Key traps are named after their shape.
Is it OK to install P-trap backwards?
The outlet end of the trap pipe should be lower than the inlet when installed properly. The example shown has it backward, which creates a trap seal more than 4” and makes the drain more likely to clog—and that’s a long explanation for why a backwards trap is a bad thing.
