Do hurricane clips go on both sides?
Dimensional Requirements. While the majority of the hurricane ties that Simpson Strong-Tie offers are one-sided (such as the H2. 5A), some are designed so the truss or rafter fits inside a “U” shape design to allow for fastening from both sides (such as the H1).
Which way do you hang hurricane ties?
For the load transfer to be successful, a hurricane tie must provide a secure connection from the top of the roof to the wall joists. A tie that does not engage the top chord of a truss, for example, could allow wind to pull apart the uppermost section of the roof.
Can you install hurricane ties backwards?
5T, H3 and H6 ties are shipped in equal quantities of right and left versions (right versions shown). Hurricane ties do not replace solid blocking. When installing ties on plated trusses (on the side opposite the truss plate) do not fasten through the truss plate from behind.
How do you put on hurricane clips?
Quote from the video:
Quote from Youtube video: This is made so that you can actually take it and you bend it actually over the top of a plate and down on each side of the studs on the wall. In order to lock the studs to the plate.
Can you use screws with hurricane ties?
Your local building inspector might approve construction screws rather than nails to attach hurricane strapping to tie down rafters to a top plate PROVIDED that the screws are properly-selected construction screws of the right size and length.
How are hurricane straps installed?
Quote from the video:
Quote from Youtube video: To make sure the roof stays in place when severe winds blow securely anchor roof to wall connections by installing hurricane straps or clips at every wall to rafter connection.
What do hurricane clips do?
What Are Hurricane Clips? Florida homes built after 2001 are required to have hurricane clips. These are steel connectors that attach your roof to your wall structure. These are designed to withstand hurricane winds that hit your walls and put upward pressure on the overhang of your roof.
How many hurricane clips are in a truss?
Each truss or rafter needs two hurricane straps: one for the front and one for the back.
How many nails are in a hurricane clip?
Classification Of A Clip
Secured to truss/rafter with a minimum of three nails. Attached to the top plate of the wall framing, or embedded in the bond beam, with less than a 1⁄2” gap from the blocking or truss/rafter and blocked no more than 1/5” of the truss/rafter. Free of visible severe corrosion.
Can you add hurricane straps?
You can install straps that connect to the rafters or trusses right over the top of the wall sheathing. Make sure that the nails hit the double top plate behind the sheathing. If you find fiber board or foam sheathing it will provide almost no connection between the double top plate and the wall below.
Are hurricane clips required in Florida?
By Florida Code, your roofing contractor must confirm you have 3 or more Nails on your Hurricane Straps if your home has an insured value of more than $300,000. Mandated retrofits shall not be required beyond a 15 % increase in the cost of reroofing, according to FBC 706.8.
How much does it cost to add a hurricane strap to an existing roof?
Tie down hardware, also known as hurricane clips, can be installed for under $10. A house sized 40′ x 30′ requires approximately 42 pieces, so providing added assurance with tie down hardware would cost between $200 and $400.
How much do hurricane clips save on insurance?
It is estimated to save about 15% – 20% if you complete the retrofit.
What is a roof toenail?
“Toe Nails” is the way a roof structure was secured to the walls until around the 1960s, and it is nails driven diagonally through the side of the roof truss/rafter into the top plate of the wall.
What are hurricane hangers?
Hurricane joist hangers – these are used to create a stable connection between your roof trusses and rafters and top of your wall. They are designed to offer strong wind resistance and ensure that the task of hurricane clips and ties is made a bit easier in keeping the roof attached to the structure.
What are hurricane roof straps?
A hurricane strap is a connector that is used to strengthen wood framed roofs and homes. The most popular hurricane straps are made of galvanized steel or stainless steel and they are designed to protect structures from the ravages of adverse weather events such as tropical storms and winter storms.
