How do I find the code on my Maytag Bravos washer?
Choose any one button on the washer’s console except Power, Start, or Stop. Press/Hold 3 Seconds – Release 3 Seconds – Press/Hold 3 Seconds – Release 3 Seconds – Press/Hold 3 Seconds. 4. If there are any saved fault codes they will be displayed.
How do I read a Maytag code?
Quote from the video:
Quote from Youtube video: Then it's three ticks to the right one tick to the left and one tick to the right and you have to be pretty precise or your timing. Or it won't engage. And then when it engages the lights flash.
What are the error codes on a Maytag washer?
Error Codes in my Maytag Front Load Washer
| Error Code | Error |
|---|---|
| Sud or Sd | There are too many suds in the washing machine. |
| F5 E2 | The door is not locking properly. |
| F7 E1 | Indicates a motor speed sensing error, |
| F8 E1 or LO FL | The washer is sensing a low flow of water. |
Where is Maytag error code?
Quote from the video:
Quote from Youtube video: Now if there are no more stored codes only the sensing fill light will be displayed flashing on and off in this case in the washer i have two error codes stored in the machine.
How do you run a diagnostic test on a Maytag washer?
This is how you get into the washer’s diagnostic mode.
Turn the washer control dial at least 3 full rotations to the left like you were clearing a combination lock. Then rotate the knob 3 clicks to the right, one to the left, and one more to the right, with about a half second to one second between clicks.
What does the code LF mean on a Maytag washer?
LF in the display
When “LF” is displayed, there could be an issue with the water flowing into the machine. Check the water inlet hoses to be sure they are not clogged or kinked. You may also need to check the screens on the washer water inlet valve.
What does HC code mean on Maytag Bravos washer?
hot and cold hoses reversed
If HC (hot and cold hoses reversed) appears in display, it means the hot and cold inlet hoses have been installed incorrectly. This code will appear at the end of the wash cycle to indicate that the cold water hose is connected to the hot water inlet, and the hot water hose is connected to the cold water inlet.
What does LR mean on Maytag washer?
The LR code means “locked rotor” which is just a way of saying the control is not seeing the motor turning. The image below contains the wiring diagram for this washer as you requested but there are some other things to consider. Usually when the LR code is displayed the motor has stopped turning for some reason.
How do I reset my Maytag Bravos washing machine?
Alternative Maytag Bravos MCT washer reset procedure (this works for some Maytag Bravos washer series models)
- Turn the dial (Cycle Selector knob) until it is at the 12 o’clock position (turn dial 1 counterclockwise or right full turn back to 12)
- Now proceed to turn the dial three (3) turns clockwise (right).
How do you calibrate a Maytag top load washer?
Quote from the video:
Quote from Youtube video: You'll then need to hold the start button for a good 5 6 7 seconds or so until the lights stop flashing. And that pulls you out of diagnostic mode so that we can then go back in and calibrate.
How do you reset the code on a Maytag washer?
Quote from the video:
Quote from Youtube video: Then press the delicates button for like three seconds and then press the extra rinse button to access the service mode menu. Once you see the P dash zero one press start and the interface is going to
What does calibrating a washing machine do?
Except for preventing vibrations and noise, calibration also makes sure you save energy. After calibration, the load sensor more accurately weighs your laundry. This means the washing cycle can better adjust itself to to the amount of clothes, which saves time and energy.
What does calibrating your washer do?
calibrate your washing machine to prevent it from vibrating and making a lot of noise. The time it takes to Calibrating your washing machine is 3 minutes.
What does AC6 mean on Samsung washer?
AC6 error is an error when the exchange of data between the control module and the information display board has an issue. Recommended Troubleshooting Tip: Switch off the washing machine and unplug the power cable from the power source and power it on again and start another washing cycle.
How do you calibrate?
On Windows, open the Control Panel and search for “calibrate.” Under Display, click on “Calibrate display color.” A window will open with the Display Color Calibration tool. It steps you through the following basic image settings: gamma, brightness and contrast, and color balance.
