Tape to old, pull new, pull back old

  1. Disconnect one end of the old cable.
  2. Tape the new cable to the old cable. …
  3. Use the old cable to pull the new cable through to the destination.
  4. Untape the new cable and pull through an additional complete length – i.e., the same length as you had to pull the first time.

How do you fish a cable from another cable?

Quote from Youtube video: Use electrical tape to secure one end of the cable to the hook on the fish tape at the wall opening steadily retract the fish tape pulling the cable into the wall opening.

How do you fish Ethernet?

Quote from the video:
Quote from Youtube video: First you'll need some cat6 wire or catch 5e cat5e is cheaper i recommend getting 500. Feet you also need some rj45 connectors. And some boots for the wires.

How do you follow a cable through a wall?


  1. Cut Box Openings. With the cable routes and box locations planned, cut the openings for the electrical boxes in the drywall. …
  2. Drill Holes in the Wall Plate. …
  3. Locate the Drilled Hole. …
  4. Thread the Fish Tape. …
  5. Attach the Cable to the Fish Tape. …
  6. Fish the Cable. …
  7. Complete the Cable Run.

How do you fish a cable outlet?

How to Fish Wire Through A Wall

  1. Route Cable Behind Baseboard.
  2. Make a Bevel Cut.
  3. Make a Chase With Trim.
  4. Don’t Fish Power Cords.
  5. Give Communication Cable Enough Space.
  6. Find the Easiest Route.
  7. Use a Lot of Cable.
  8. Hide Wires With Raceway.

How do you trace a wire without power?

Quote from the video:
Quote from Youtube video: Device some tracers such as this one require that the wires that you wish to trace not be energized this means they're not receiving any power from any source.

How do you fish Ethernet cable between floors?

Quote from the video:
Quote from Youtube video: Now after you get it to downstairs you need to open up another hole of course to retrieve that end. And get the cable. Out. After you do that. And you're satisfied then you close this up.

How do you fish wires horizontally?

Quote from the video:
Quote from Youtube video: The only thing you have to do is press the trigger real slow and reverse. And then you have it reverse again and then you can pull out the speaker wire.

How do you use cable fish tape?

Quote from the video:
Quote from Youtube video: This is how you do it just hang on to here. And pull the handle hang on pull the handle pull the handle pull mmm. And that just zips it on out.

How do you fish wire through the ceiling without an attic?

Quote from the video:
Quote from Youtube video: What you would do is you'd actually most houses today have are littered with recessed cans. That's good if you want to run wires. Because then you have access all over the place.

How do you fish a cable through a ceiling?

Use a 3/4-inch bit or a hole saw of similar size. These holes will allow the wiring to pass through the wall framing. Alternatively, use a saw or chisel to create a notch 3/4 inch wide and 1 inch deep in the face of the top plate and across the face of each stud the wiring travels over.

How do you fish through a HDMI ceiling?

Registered. The simplest way is to unhook one of your existing cables and tape a string to the end. When you pull it out, you pull the string in. Then tape the HDMI cable along with the existing cable to the string and pull them both back in through the two horizontal studs.

Can you run electrical cable horizontally?

Horizontal runs are absolutely fine, as stated above, if you shift a socket across that has a vertical feed there must be a fitting at the point where the vertical feed drops down to meet the horizontal to mark the end of the vertical, that can be a socket, or a spur, or indeed just a blanking plate.

Can a cable pass through a back box?

Yes cables passing through a back box take up space so you use a deeper box (35mm) but apart from that why would the third party electrician even have a notion that this practice goes against regs.

How long can a spur cable be?

The unfused spur should supply just one single or one double (twin) socket outlet. It should be wired in 2.5mm2 P.V.C./P.V.C. T&E cable. There is no limit to the length of a spur, but Voltage drop considerations should be taken into account.

Can cables be run diagonally?

Plenty of real tradesmen run cables diagonally when it is appropriate and without using metal conduit.

Can you bury cables in walls?

Burying a cable in a wall is a traditional way to hide and protect the cable. Modern cables can be buried directly in plaster, or protected with capping before plastering. Before a cable can be buried however, a chase needs to be cut!

Do electric cables run up or down?

These zones will always run vertically down the corner. Horizontally from any switch or socket – The zone runs horizontally from both sides of the socket or switch until it reaches a corner or an obstacle such as a door.