Can you run PEX next to ductwork?
Being close to Ductwork is fine, the hot water is hotter than the ductwork will ever get. FYI, the Blue PEX is just coloring and is exactly the same as the Red PEX.
What is the best location for HVAC ducts?
Air Ducts Near the Ceiling Are Most Effective
One of the most important things to be aware of when deciding on vent placement in your new home is that typically, air ducts placed near or within the ceiling are the most effective option in terms of energy efficiency.
What can go wrong with ductwork?
Hot and Cold Spots, Inconsistent Room Temperatures
Undersized ducts and grilles restrict airflow and may be the cause of your comfort and temperature problems. If you notice loud airflow and strange noises such as whistling and popping, you may have improperly sized ducts or blocked vents and registers.
Where should I put my return and supply ducts?
They must be correctly placed and unobstructed —Return ducts are usually placed in hallways, under stairwells, or in larger open areas of your home. This placement ensures that they will be able to pull in enough air to take back to the HVAC equipment.
Can you run plumbing through ductwork?
So, can your plumbing run through ductwork? The short answer: no. Any ducting system has the chance to run excessively hot or cold air. With that in mind, there is always a chance that hot air may cause damage to your pipes.
How close can PEX be to water heater vent?
6 inches
PEX tubing may be connected directly to residential electric tank or tankless (instantaneous) water heaters, if the local code and manufacturer’s instructions allow. When connecting PEX tube to gas tank or tankless water heaters, the tube must be kept at least 6 inches away from the exhaust vent of the heater.
Can you use the same ducts for heating and cooling?
One of the main ways that homeowners can consolidate ductwork is by switching to a central HVAC system. With a central air conditioner, you get cooling in the summer months, heat in the winter, and all with the same use of your existing ductwork. This reuse is a great way to cut down on installation costs as well.
Can I tap into existing ductwork for basement heat?
Yes, you can tap into existing ductwork to heat the basement. It is a permanent solution that will warm your basement in the cold season without hiking the electric bill. While you can use the existing ductwork, there are other cheaper ways to heat the basement without it.
How do you reroute ductwork?
Quote from the video:
Quote from Youtube video: And this little they're just simple screws that screw it all together or in sections you may pull right out and we'll remove it put in the windows. And move the duct. Over.
Do you need a return duct in every room?
While it is a myth that air return grilles are required in each and every room in the house, it is definitely necessary to have more than one of these grilles installed at strategic places in the house. The most important place to have these would be the bedroom.
How far away should a return vent be from a supply vent?
Return vent on wall adjacent to wall of supply vent. The return vent would be approximately five feet away from the supply vent.
Do you have to open walls to replace ductwork?
Quote from the video:
Quote from Youtube video: The only fix is to tear open the walls and the ceiling. To get at that duct and replace it what say. You. If it's sweating. And it's what it is if it's sweating.
Can I use PVC pipe for ductwork?
PVC is durable and not prone to corrosion or denting, which makes it a good option for ductwork. Because it resists moisture, PVC is preferred when you install ductwork directly beneath the floor in a building with no crawl space.
Is PEX allowed in return air plenum?
A return-air plenum is an un-ducted ceiling space being used for air circulation. It’s important not to have PEX-a Pipe Support segments less than 48 inches long in a return-air plenum, and the space should not have more than 18 inches of bare PEX or fittings.
Can you use PVC pipe for central heating?
Plastic pipes must not be used to connect a boiler, nor must they be used for Gas.
Can PEX be used for central heating?
Built for speed. Not for cheaters! Designed for radiator heating and potable water applications, Uponor PEX Plumbing systems combine speed of installation, with our new expander tool, and the security of the connection.
Can you use PEX pipe for heating system?
Yes, PEX pipe is approved for radiant or hydronic heating applications. Since ferrous components are likely to be present in the system, it is important to use oxygen barrier PEX pipe to help prevent ferrous components from rusting.
Can you use flexible copper pipe on central heating?
Flexi’s are NOT suitable for use on CH.
Is plastic piping better than copper?
PROS: Resistant to corrosion, abrasions, and impact damages better than copper pipe because plastic doesn’t corrode. PVC pipe is thicker than copper which also helps with impact damages and abrasions. Less noise compared to copper piping, even with higher water velocities and speeds.
Are plastic plumbing pipes better than copper?
Unlike plastic copper is metal based, when combining water and air, a corrosion can take effect and over time the copper can disappear. Plastic does not corrode under water and air, however there are other factors where the rubber seal, if knocked can leak due to the rubber overtime going hard.
