What is the live load for a deck?
40-psf
For a residential deck, the code requires it be designed to support a minimum 40-psf live load. The live load is the external force applied to a deck due to the activities of its use. People, furniture and any other movable, physical objects on the deck are covered under live load.
What size wood should I use for decking frame?
Commonly used joist sizes are 2-by-6, 2-by-8 and 2-by-10. For example, when you space joists 16″ apart — which is standard for residential decks — a deck spanning 9 1/2′ would require 2-by-6 joists, a 13′ deck would need 2-by-8 joists and a 16′ deck calls for 2-by-10 joists.
How much gap do you need between pine decking?
3-6mm
Treated pine decking will take up or lose moisture depending on dryness or moisture from the environment, causing the timber to expand or contract. Ensure gaps are provided between the decking boards which will allow for the expected expansion. Generally 3-6mm.
Should you leave a gap between decking boards?
Determining Deck Board Spacing
When using wood decking, you want a gap of at least 1/8 of an inch after your decking has dried out. If you’re using decking that’s already been dried out, you can leave a 1/8-inch gap when you install. Many decks will use “green” wood, or wood that hasn’t been dried down or kiln dried.
Can you use 4×4 posts for a deck?
In the past, many decks were built with 4×4 support posts (also called structural posts). But these can bow seriously, even if a deck is only 3 feet off the ground. For that reason, we strongly recommend that you use 6x6s instead, even if your building department does not demand them.
How do you know how much weight your deck can hold?
If your deck is built to code, then it is designed to hold a minimum of 50 pounds per square foot, of which ⅘ of that total is the “live” load. Therefore, a deck of 120 square feet multiplied by 50 shows that your deck can hold 6000 pounds, including the structure.
Can I use 4×2 for decking frame?
4 x 2 Timber Rail / Joist. Pressure treated timber joists. These decking joists are the most common sized framing timber for decking. They provide a solid structure for fixing your decking boards too.
Should I use 2×4 or 2×6 for deck?
Most builders stick to using a minimum of 2x6s for deck floor joists. If you want to add guardrails and stairs, you need at least 2x10s. 2×4 and 2×6 joists are ideal for ground-level decks without guards.
Should deck joists be 2×6 or 2×8?
For upper-level decks, 2×10 is recommended as the minimum size to use for strong guard post connections. 2×6 joists should only be used on ground-level decks that do not require, and will not provide for, any guards.
How far can 5 4 deck boards span?
If you use 5/4 decking, joists must be no farther apart than 16 inches. Decking made of 2x4s or 2x6s can span up to 24 inches.
What happens if you don’t leave gaps in decking?
Rain can prove especially detrimental to wood decking if it doesn’t have a place to drain off the deck. When there are no gaps between the boards, this moisture remains trapped which can lead to issues like rot and mold.
Do you screw decking at every joist?
Each deck board should be fastened with two screws at each point where the board crosses a joist to ensure the stability and durability of your deck’s surface. Boards should be fastened to rim joists with three screws.
How many screws do I need for 5 4 deck boards?
The general rule of thumb for standard deck fasteners is 350 screws for every 100 square feet of decking, which is based on standard 6″ wide boards (5-1/2″ actual), and 16″ joist spacing.
Is it better to nail or screw a deck?
For the decking boards, many agree that screws perform better than nails. They have better tensile strength and will less likely to pop out, which is a common problem in decking. Many also agree that nails are better used for the frame of the decking.
Which side of deck board goes up?
A board that is correctly installed right side up (or bark side down) will form a crown and allow water to run off the edges. If the board is installed wrong side up (or bark side up) it will curve up on the edges when dry and water can gather and sit in the cup. That is a recipe for wood rot and problems.
Does it matter which way deck boards run?
The default direction decking runs on an attached deck is parallel with the house. A few reasons for this are deck framing construction, water runoff and appearance. Decking running parallel to the house is beneficial structurally, aesthetically and costwise.
Which way up does treated pine decking go?
What is the correct way to lay decking? Any decking board manufacturer or professional will tell you: “The proper way to install a decking board is ridge side down.” The ridges are designed to allow for airflow, to stop moisture sitting in the ridge, and allow for a stronger structure.
What is the correct way to lay decking boards?
The correct way to lay decking boards for most decking is smooth-side-up, with the ridges there to prevent rot and mould.
How do you stagger deck boards?
A common method for staggering a deck is to start the first row with a full plank, then cut one-third of the next row’s first board off the end. The row after that has an additional one-third cut off and then repeat when you get back to a full board.
Why do decking boards have grooves?
In the USA, where timber decking extremely popular, the smooth deck board predominates. In Australia, they advocate to use the grooves face down stating that grooves or reeds on a decking board are designed to allow for airflow underneath the boards to stop moisture and mould build up.
