They are typically located in the middle of the shower floor, and the floor is sloped from all directions down to the drain. The shower floor is really a gently sloped funnel that directs all of the water into this drain. One tip is to look for a square drain grate, as opposed to a round one.

Where should shower drain be placed?

The drain in a shower should ideally be the lowest point of the shower floor. A correct shower floor generally has a slope to it instead of a level surface. So, the positioning of the drain is such that water from all directions slopes down to the drain.

How far is a shower drain from the wall?

Rough-In Dimension Terminology

Toilet Shower/Tub
Discharge/Drain Hole from Back Wall 12 1/2″ 14″
Discharge/Drain Hole (Vertical) 0″ 0″
Fixture (Side to Side Buffer) 15″ to 18″ min 18″ min
Fixture (Front Buffer) 21″ min 18″ min

Should a shower drain be in the middle or end?

No, shower drains don’t need to be in the center. As long as the drain is at the bottom of a slope so water will flow into it, your drain will work just fine.

Can the shower drain be in the wall?

WallDrain offers the ultimate in shower luxury and design innovation, pushing performance to its limit. It breaks the traditional rules of shower drain systems and goes beyond the limits of convention. Because WallDrain is built into the wall instead of the floor surface, it offers a totally concealed and sleek look.

How high should a shower drain be?

2″ Drain Pipe should be centered in a hole (approximately 5″ diameter) in the flooring. The top of the Pipe should be no higher than, and no more than 1/8″ lower than, the top surface of the floor on which the base will be set.

Does it matter where the drain is in the tub?

Why does this matter? Because the location of the drain correlates to the plumbing and drain assembly located beneath it. This means that you wouldn’t be able to select a new tub that has a different drain location than the one you are replacing.

How do you rough in shower drain?

Quote from the video:
Quote from Youtube video: Put your level on top of it in this case of torpedo level. Right. Unexpectedly so you put your pork torpedo level on the pipe as you drive fit it and to the p-trap. And if you notice at a top level.

How far can P trap be from shower drain?

Under both the IRC & UPC the maximum length of the tailpiece is 24″ vertical from the finished edge of the drain opening to the standing water level in the trap except washer standpipes.

How far can shower drain be from vent stack?

The connection between the fixture drain and the horizontal drain and vent pipe is the only vertical pipe of a combination drain and vent system. 8 feet is the maximum vertical distance.

How far from the wall is a tub drain?

Bathtub Drain Measurements



The drain hole should be a minimum of 12 inches away from the wall and 9 inches in scope. To rough in the drain, use a 1.5-inch pipe.

Should the shower drain be flush with the floor?

Should The Shower Drain Be Flush With The Tile? Yes, the shower floor’s drain should be flush with the tile around it at the point where the two meet. However, according to experts, point or center drains in tile require a 1/4-inch slope per square foot from all four sides of the drain.

How high should the shower drain be before tiling?

Step 1: Floor Tile Must Slope to the Drain



In a stall shower, the plumbing code requires the floor to be sloped one quarter (1/4) of an inch per foot in order to carry the water effectively to the drain. This slope, according to the TCNA Handbook is called “sloped fill” or commonly known as the pre-slope.

Can showers have a one and half inch drain?

Current plumbing codes (IPC as well as MA Plumbing Code 248 CMR 10 for instance) need 1.5 inches to drain for a tub with a shower. The tub can drain at leisure and the shower function when in utilize, with flow-limiting showerheads, fall within the flow rate that a 1.5” drain can handle.

How do you rough in shower drain?

Quote from the video:
Quote from Youtube video: Put your level on top of it in this case of torpedo level. Right. Unexpectedly so you put your pork torpedo level on the pipe as you drive fit it and to the p-trap. And if you notice at a top level.

How far should bathtub drain be from wall?

Bathtub Drain Measurements



The drain hole should be a minimum of 12 inches away from the wall and 9 inches in scope. To rough in the drain, use a 1.5-inch pipe.

Does shower head need to be centered?

If your shower head isn’t centered, the water could drench your entire bathroom floor space. And if you mount the shower head more towards a window or the wall, you would barely be underneath the water, making it a very unsatisfactory shower.

Should shower valve be centered with drain?

When possible it’s best to design a shower with an off-center drain. Think about it, if the drain is in the center, you are likely to be blocking it with your feet while you are taking a shower. This can slow the draining process.

How far should shower head be from ceiling?

Let’s tackle the most important question right away by pinpointing the standard height for a shower head. According to Hunker, the industry standard for how high a shower head should be is 80 inches.

Where do you put shower controls in walk in shower?

Install wall-mount shower controls 48-52 inches above the floor; place the controls so they are accessible from inside and outside the shower. Mount showerheads 69-72 inches above the shower’s floor. Keep in mind that sprays from traditional showerheads extend as much as 4 feet.

How far can shower head be from valve?

But for other showers, you can measure the distance from your shower head to the valve. If the showerhead is at 80″ then a good height is about 45″ above the ground. To make things easier, you can always go exactly halfway between the floor and the showerhead. In this case, it would be 40″ between the two.