The easiest way to connect faucet water supply lines together is by using a compression fitting. Measure your line diameters carefully and purchase the same size compression fitting to join them.
Can you connect 2 water supply lines together?
Connecting two faucet supply lines is best done using a compression nut fitting. The easiest way to do this is to measure the pipe and purchase a compression fitting that matches the size. Joining the lines to the fitting may involve different procedures depending on specifications, but it is never complicated.
How do I combine two supply lines?
Quote from Youtube video: Using one wrench to stabilize the stop and the other to tighten the connection wrench tighten one half turn after the nut begins to hold or fight thread both connectors onto the valve.
Can I tie into an existing water line?
The most common way to connect a new drain, vent, or supply line to an existing line is to install a tee fitting. To do so, shut off water to existing supply pipes and drain the lines. Flush all toilets and caution others not to use drains.
How do I extend my water supply line?
Quote from the video:
Quote from Youtube video: So when you remove that nut and i think there's also a little kind of coupling thing in there a compression thing anyway um that will allow you to extend this hose uh into the supply.
How do you connect two braided water lines together?
Quote from the video:
Quote from Youtube video: Taking your knife sliding. It on first that goes up into the faucet. I'm taking your 3/8 compression nut it's like so 3/8 brass ferrule dropping that place tightening it up and turning your water on.
How do you connect hot and cold water?
Quote from the video:
Quote from Youtube video: The sink so you're going to have to reach behind the sink. Find that threaded pipe hanging down and thread on the supply. Line just and just make that hand tight.
How tight should water supply lines be?
It seems to go against common sense, but plumbing fittings don’t have to be super tight in order to function properly. In fact, pipes should only be hand tight to help aid the flow of water throughout your home.
How do you connect faucet lines?
Quote from the video:
Quote from Youtube video: Turn the nut counterclockwise. Until the threads align. Then turn the nut clockwise. And hand tighten until you hear a click the click lets you know it's sealed slowly turn the water supply valve.
Do faucets come with supply lines?
Measure for Supply Tubes
New faucets often come with supply tubes included, but these tubes aren’t always long enough or equipped with the correct threads for connecting to the shutoff valves.
How do I extend my copper water pipe?
Quote from the video:
Quote from Youtube video: You can join copper and plastic with a lot of the same fittings a lot of people don't realize that you can actually join a piece of plastic pipe with a compression fitting.
Can a faucet supply line be too long?
Ignore the Length
The hot water may be delayed for one or two seconds, but the water pressure will be unaffected. The only downside to a longer-than-necessary flex line is that the line will bunch up beneath the sink, taking up some valuable room.
How do you extend a pipe under a sink?
Quote from the video:
Quote from Youtube video: So you need the proper washer insert the retention nut. And the nylon washer. And loosen up there p-trap. And install the extension tail piece. And stole another retention nut.
What is a slip joint extension?
The Danco Slip-Joint Extension Tube is designed for use in tubular sink drain applications. It is constructed from durable plastic that will endure the rigors of everyday use. This tube extends 12 inches for additional reach for drain connections. Model # 51669.
What if new kitchen sink drain doesn’t line up with existing pipes?
In general, if the P-trap doesn’t line up with the drain, you can adjust the length and height of your drainpipes by cutting them or simply slipping them in and out of their fittings.
What is a trap adapter?
PVC Threaded Trap Adapter to connect your sink drainage to the drain pipe that extends through the wall or floor. Designed to fit most tubular drain applications, this universal adapter is constructed from PVC plastic. Features slip joint inlet and 1-1/2 in. Schedule 40 solvent weld outlet.
How do you install a slip joint adapter?
Quote from the video:
Quote from Youtube video: Once the PVC cement is applied to the Marvel connector and the stub out there slide the mod will connect your unsub out and twist.
How do you use a trap adapter?
Quote from the video:
Quote from Youtube video: Apply it to the trap adapter. And to the drain. Line. Now you push as far as possible. And hold it for 10-15 seconds. Now you can release it and this is how you install trap adapter for the climax.
What’s the difference between an S trap and P-trap?
With an S-trap, the drainpipe drops down from the sink and into a conventional trap. It then loops over and exits downward. In a P-trap configuration, the drain also comes down from the sink and into the trap, but instead of looping over and back down, the drain enters a horizontal run before exiting downward.
Why is s trap not allowed?
The “S” trap is prohibited under the Uniform Plumbing Code throughout the United States. This is because the “S” trap will siphon or suck water out from the trap which will end up releasing methane (sewer) gases into the home.
Does P trap need to be below drain?
It is not ideal to have the p-trap below the the exit drain because water gravity has to force the water out instead of it flowing downwards naturally. They both work and have seen it many times. But essentially anything below already creates its own p-trap- so using another is redundant.
