Can you modify electrical boxes?

Adding an electrical receptacle or switch to an existing box can make it too crowded, but you can remove the old box and add a larger remodeling box without destroying the wall.

How do you do a knockout on electrical box?





Quote from the video:
Quote from Youtube video: You'll notice that the Knockouts has spot welds which connect them to the load Center. This one has one so you go to the opposite. And that's where you'll knock it out this one has two.

What is a knockout on a junction box?

Knockouts are partially stamped, quarter-size openings in the electrical boxes that service such things as outlets and switches. Once removed, a knockout allows electrical wires to be run in and out of the box. Photo: homedepot.com.

What would a knockout be used for in a metal box?

Electricians typically use a tool known as a knockout punch for cutting new holes or enlarging existing holes in metal boxes. These tools incorporate a set of dies and punches, along with some kind of device to pull the two pieces together to punch a hole in the metal box.

How do you install a surface mount electrical box?

Quote from the video:
Quote from Youtube video: Surge impact driver to drive the screws into the underside of the truss. And this will make up what's referred to as a surface mounted junction.

How can I secure my electrical box without studs?





Here’s how to install an electrical box without a stud using a winged remodel box:

  1. Trace the outline of the box onto the wall.
  2. Use a keyhole or drywall saw to cut out the shape.
  3. Thread the cables into the box and secure them.
  4. Push the box into the hole and ensure everything is snug how we like it!

What size are knockouts on electrical boxes?

Stimpson offers Electrical Knockout Plugs in six basic sizes: 1/2”, 3/4”, 1”, 1-1/4”, 1-1/2”, and 2”. Variations for special situations are also available.

How many wires are in a knockout?

Never run two cables into the box through the same knockout opening with pre-installed cable clamps. Each cable requires its own knockout opening and clamp. For installed clamps (whether they’re metal or plastic), no more than 2 wires should be installed in each connector of this type.

How do you use a knockout punch?

Quote from the video:
Quote from Youtube video: With your die insert that in the hole that you just made on the opposite side of the material take your punch. And thread that out threat. Until it's tight on the material.

Where do I punch to knockout?



The best place to deliver a knockout punch is to the head. Specifically, the boxer should aim for the chin, the lower jawline and the base of the neck. A direct hit to these areas will almost certainly drop the boxer, which is why protecting the head and the chin is the first thing young boxers learn how to do.

How does a knock out tool work?

“The Force Logic system speeds the knockout process by allowing punches and dies to be quickly aligned on the work surface without the weight of the tool. The user then snaps the tool onto the punch-and-die assembly and pulls the trigger to punch the hole.”

How do you remove knockouts from plastic electrical boxes?

How to Remove Electrical Knockouts on a Plastic Enclosure

  1. Place a flat-head screwdriver into the slot of the electrical box knockout that is to be removed. …
  2. Hit or tap the end of the screwdriver to remove the knockout and dislodge the rest of the knockout by hand if needed.



Do you break tabs off plastic electrical boxes?

Fiber boxes often have knockout ports with no clamps anyway. On non-metallic single gang boxes 2 1/2 x 4, the cable does not need to be clamped if it is secured within 8 inches of the outside of the box (NEC 314.17(C) Exception). Therefor, on those, if the tab breaks off, no issue.

How do you ground a plastic electrical box?

Because they are plastic, there is no need to attach a ground wire to it. Since it is made of a non-conductive material, switches and outlets cannot short out if they touch the side of the box.

How do you remove knockouts from a junction box?

Knockouts are usually pretty easy to remove if you are working from the outside of a junction box. If you can only access a knock out from the inside of the box, drive a self tapping sheet metal screw into the knock out and use your lineman pliers to wiggle the screw back-and-forth to remove the knockout.

What is a knockout in an electrical panel?



Knockouts are the places where an electrical box has been punched through to allow for wiring, so connections for outlets, light fixtures or additional wiring can be made within the box, which is rated to resist fire if anything overheats.

What size is a 3/4 knockout?

1.109 inches

The nominal knockout diameter for 3/4 inch conduit is 1.109 inches.