How do I lower the PSI in my pool?

You can reduce the pressure in your swimming pool pump by cleaning out its filters.

  1. Shut Down the Pump. Turn off your pool pump and filter. …
  2. Remove the Cover. …
  3. Take Out the Pump Basket. …
  4. Rinse the Pump Basket. …
  5. Remove Any Debris From the Impeller Port. …
  6. Replace the Cover. …
  7. Examine the Air Relief Valve. …
  8. Monitor the Water Pressure.





How do I get rid of the bubbles in my pool pump?

Quote from the video:
Quote from Youtube video: Make sure that it's seated and make sure that there's not any grit. Or debris that might be obstructing. The lid. From getting a nice good secure close. So first water level in the pool.

What causes high PSI in pool pump?

High pressure usually indicates a dirty pool filter, time to backwash or pull out the filter cartridge for cleaning. Be careful with high filter pressure, as filter tanks can rupture with deadly force.

How do you fix a high pressure pool filter?

Quote from the video:
Quote from Youtube video: Number one clogged filter. The most common problem leading to high pressure is a clogged or dirty filter. Over time the creases in a cartridge filter get embedded with fine debris oils.

What happens if pool filter pressure gets too high?





A pool filter requires a certain amount of pressure inside the tank to function. If that pressure gets too low or too high, the filter won’t work properly, and it can damage other equipment.

What PSI should a pool pump run at?

For pool owners, the normal range is around 10 PSI; check your owner’s manual for more information. Once you know what’s normal for your filter, get in the habit of checking the pressure gauge once a week as part of your pool maintenance routine.

Why is my pool water bubbly?

Foam in a pool is due to the water being “thick.” This thickness creates bubbles. The bubbles are filled with air that can come from your pool circulation system that return the water back into the pool or even the wind outside. Common causes of foam are: Hair care products – shampoo, gel, hairspray, etc.

Why is my swimming pool foaming?

Finding foam in your pool usually means there’s a high organic load in the water. In other words, more organic material than can be dissolved in the water, or eradicated by sanitizer. This causes the water to “thicken.”

Why is my pool pump gurgling?



Gurgle – A gurgle noise coming from your pool pump could be caused by air leaking into your system even if no water is leaking out. Air could come in from the pump basket lid or could be getting sucked in through the skimmer or other pipes. Gurgling noises can also be a result of not priming your pump correctly.

Where is the air relief valve on a pool filter?

Run the filter and open the air relief valve on top of the filter. It is typically a small handle-like protrusion on the top of the filter near the pressure gauge. Listen for the hiss of air escaping from the valve.

What pressure should a pool filter be at?

On average, a pool filter cartridge’s pressure reading, in PSI on the filter gauge, should read between 8 – 15 PSI. If you are experiencing an 8-10 PSI increase in pressure, somewhere up around 25-30 PSI or higher, this means that it is time for you to clean your filter!

At what PSI should I backwash?



8-10 PSI

Another industry standard is to backwash when your filter’s pressure gauge reads 8-10 PSI (pounds per square inch) over the starting level or “clean” pressure. For example, if your filter is running normally at 15 PSI but increases to 25 PST, you should perform a backwash.

Can a pool filter explode?

The filter operates under high pressure generated by a mixture of water and air. The lid can explode off the tank with tremendous force if too much pressure builds up and the clamp fails. Because of the extremely high pressure that can build in the filter and result in an explosion, a failure can be catastrophic.

How many hours a day should you run your pool pump?

approximately 8 hours a



Every pool must turn over at least once a day, so most pool pumps should run approximately 8 hours a day. But here’s the thing: you don’t have to run your pool pump consecutively. You can choose to run it for three hours in the morning before you leave for work and another 5 hours in the evening.

Can a pool filter electrocute you?

You can get electrocuted in a swimming pool as a result of: (1) faulty electrical wiring to pool equipment such as underwater lights, pumps, filters and vacuums; (2) no GFCI (Ground-Fault Circuit-Interrupters) protections for outlets and circuits; and (3) electrical appliances and extension cords entering the water.

How do I know if my pool filter is working properly?

Add diatomaceous earth (DE) to your pool skimmer, stick to around a scoop or two – no more than the size of a 1lb coffee cup. The moment you do this, go to the pool jets to see if it is returning DE into the pool, or if the water suddenly looks cloudy. If it is, you likely have an issue with your filter.

What PSI should my sand filter run at?

Generally speaking, a pressure reading between 10 – 25 psi can be considered normal. Once you have installed a new filter, turn everything on and take a baseline reading. Each time that you change your pool filter take a new baseline reading.

Why is my pool not filtering properly?



If the water is not moving through the filter at a normal rate, there is most likely a clog or obstruction before the pool filter. It could be a clogged pump basket, impeller, pipe, or skimmer basket. It could also be a closed or broken valve before the pump.