Why is heat not working with Nest?

You first need to make sure that your thermostat is not defective. Turn off power to your furnace, then join together the Rh and W wires (take them out of the nest wire plate and join them with a small wire nut or just twist them together), power back your furnace and check if your zone is working properly.

Why is my heat not working on thermostat?





The most common reasons for such a problem are a dirty filter, thermostat malfunction, pilot ignitor, wrong settings, or low battery issue. In such a case, all you would have to do is clean the device, double-check the thermostat settings, or replace the batteries.

How do I fix my Nest wiring problem?

Quote from the video:
Quote from Youtube video: But if there's only one wire it should go into the RH port if that doesn't work try putting the red wire in the RC port to see if it registers.

What wire controls heat on Nest thermostat?

W1 wire

The W or W1 wire controls your heating system. In most systems, the Y or Y1 wire controls your cooling system. If you have a heat pump, your Y or Y1 wire controls your compressor.

Why is my Nest blowing cold air on heat?





If your system starts to blow cool air when your Nest thermostat is in Heat mode (or if it blows warm air when its in Cool mode), change the settings for orientation of your heat pump. The instructions depend on which thermostat you have.

How do I force Nest to heat?

Nest Thermostat

  1. Open the Home app .
  2. Touch and hold your device’s tile.
  3. At the top right, tap Settings Thermostat. Emergency Heat.
  4. Tap the switch to turn it on or off.


What do you do when your heat won’t turn on?

What to Do When Your Furnace Won’t Turn On

  1. Check Your Circuit Breakers. Even if you use a gas or propane furnace, some of the components run on electricity. …
  2. Check Your Thermostat. …
  3. Check the Drain Pan. …
  4. Check Your Air Filter. …
  5. Check the Pilot Light. …
  6. Check Your Natural Gas or Oil Supply.



Why isn’t my heat working in my house?

Dirty filters are the most common cause of furnace problems. Dust and dirt restrict airflow—and if the filter gets too clogged, the heat exchanger will overheat and shut off too quickly, and your house won’t warm up. If the blower is running but no heat is coming out, replace the filter.

Why is my central heat not turning on?

When you find your home central heater not working, there could be several causes. Two of the most common reasons your home central heating isn’t working are a dirty flame sensor and a dirty air filter. Clean the flame sensor with a steel wool pad and replace the air filter every 1-2 months.

Does your heat pump use an O wire or B wire?



On many other thermostats, the O wire is typically connected to a terminal marked W on one side and O or O/B on the other side; the W is for use with a conventional system (furnace) while O/B is for use with a heat pump.

Is RC and C wire the same?

No the Rc is the red wire. You need 5 wires or more for this to run with all the functions. You can use one of the other wires but you have to drop control of the fan. It will only come on when furnace comes on.

Does Nest need RC and RH?

The Nest Thermostat E only has an R connector, which is typically where an R wire would go. If you have separate heating and air conditioning systems, you might have separate Rh and Rc wires that come out of the wall and are connected to your system.

Does red wire go to R or RC?

If you have both an Rh (Red-heat for powering the heating) and an Rc (Red-cool for powering the cooling), then the R wire can be connected to either Rh or Rc. If you only have a single R wire, then it will only have an R connector, which is the connection you’ll use.

Why does my Nest say no power to Rh wire?



Quote from the video:
Quote from Youtube video: And it's caused by the float switch on the air handler detecting that the condensation.

Do I need a jumper from R to RC?

If you have a wire in the R terminal, and another wire (not a jumper) in the RC terminal, you will not need to connect the R and RC terminals. See our Basic Wiring article for more info here.

What is the difference between RC and RH on a Nest thermostat?

There is no standard for the colour of the RH wire, but most units use a red one. The RC wire, on the other hand, refers to “red cooling”. It’s the same with the RH wire in that it powers the thermostat. For the RC, it powers the cooling system.

Is RC wire same as R?

RC is no different and simply means red cooling. The wire is generally red, although there is no color standardization — but more importantly, the “R” really means that the wire and terminal are hot; it’s a live electrical wire. The RC wire connects to the RC terminal, which controls the cooling system.

What is the Blue C wire on a thermostat?



heat pump

C wires or varying colors apply to every thermostat, but blue C wires belong to thermostats attached to a heat pump. Blue wires are for heat pumps, like orange wires. This wire connects to terminal B on your thermostat.

How do you jump a thermostat for heat?

  1. Step 1: Switch Off the Power. Locate the switch for the furnace or air system and turn it off. …
  2. Step 2: Expose the Thermostat Wires. …
  3. Step 3: Find the Power Wire. …
  4. Step 4: Twist the Wires Together. …
  5. Step 5: Turn On the Power.