The purpose/advantage of an old work box is that you use it where there is no stud to attach to. The tabs bind it to the drywall. If you use the tabs then you do not need to screw it to a stud. IF you have a stud to attach to then you would use the box that jack recommends in his answer.

Do electrical boxes need to be attached to studs?

They don’t need to be fastened to a stud, so you can install them anywhere. There are several types.

How do you secure an old work electrical box?

Quote from the video:
Quote from Youtube video: The box and feather the opening with the edge of the utility knife until the box fits snug to install run wires into the box and position it in the hole.

How do you install an old work Junction box?


  1. Prepare the Retention Tab Screw. …
  2. Prep the Box’s Cable Clamp (PVC Boxes Only) …
  3. Prepare the Electrical Box Opening in the Wall. …
  4. Run Cable and Strip the Sheathing. …
  5. Insert the Cable into the Box. …
  6. Insert the Old Work Box Into the Wall. …
  7. Strip Wire Insulation from the Conductors. …
  8. Final Steps.

How do you secure an electrical box in the wall?

  1. Step 1: Trace Box. For your safety, turn off power before starting this project. …
  2. Step 2: Cut Hole. Cut the hole with a drywall saw. …
  3. Step 3: Thread Cables. Run cable through the hole. …
  4. Step 4: Insert Box. Push the box into the hole. …
  5. Step 5: Secure Box to Wall.
  6. How do you install metal old work box?

    Quote from the video:
    Quote from Youtube video: They would just go up against the sides top and bottom of the box if it was a fully enclosed. Device. Box put that into the hole. Into the opening. Snap it in tight.

    Does an electrical junction box need to be secured?

    The cables are secured to the box with cable clamps (or conduit connectors, if the circuit includes conduit), and the box must have a removable cover to create a complete enclosure. Junction box covers must remain accessible; they cannot be covered with drywall or other surface material.

    How much weight can an old electrical box hold?

    50 pounds

    The B618R is a round old work outlet box and is not listed for fixture support in the ceiling. Only approved ceiling boxes are allowed to support fixtures in the ceiling. These boxes will be permitted to support a minimum weight of 50 pounds. The B618R can be used in the ceiling as a junction box.

    How do you remove an old metal electrical box?

    Quote from the video:
    Quote from Youtube video: To cut the other rail he's a dremel tool with a one and a half inch cutting wheel designed to cut. Metal. I'll have to cut the last bit of it with a saw I'm gonna pull it down apart.

    How do you install an electrical stud box?

    Quote from the video:
    Quote from Youtube video: Just pinch the box firmly against the stud with one hand and tap the nails into the framing with your other. Making sure to synch them fully. So the box is tight to the.

    What screws to mount electrical boxes?

    The most common electrical box screw sizes are 6-32 and 8-32. Be sure to get round head or hex-head screws for inside the box, to prevent arcing. Use oval-head screws to attach cover plates.

    Are electrical outlets on studs?

    Studs are sometimes located next to electrical outlets and light switches. Often times, locating studs is as easy as finding your electrical outlets and light switches. Standard outlets and light switches are fastened to studs. Remove the outlet or switch cover, then look inside the electric fixture.

    How do you install a metal electrical box without studs?

    Here’s how to install an electrical box without a stud using a winged remodel box:

    1. Trace the outline of the box onto the wall.
    2. Use a keyhole or drywall saw to cut out the shape.
    3. Thread the cables into the box and secure them.
    4. Push the box into the hole and ensure everything is snug how we like it!

    Do junction boxes need to be mounted?

    Often known as a junction box, this metal or plastic box includes a cover to protect the wiring within and protect you from the wiring. This rule is demonstrated nicely by wall switches, receptacles, and standard light fixtures, all of which require a junction box to mount the device and house the wiring connections.

    How do you install an old electrical box in a ceiling?

    Quote from the video:
    Quote from Youtube video: You can also cut the hole manually with a jab saw I took the drywall circle out and put the new electrical sealing box in place.

    Can you use old work box in ceiling?

    Quote from the video:
    Quote from Youtube video: And the way it works is unlike. The new work box which is attached directly to the stud. This is actually going to be hanging on the drywall.

    How do you secure a drywall outlet box?

    Quote from the video:
    Quote from Youtube video: And cut out the drywall. After your holes cut out go ahead and take your box. And slide it into the hole. Then we're going to take our drill. And tighten up these screws.

    What is a pancake electrical box?

    Round Pan Electrical Boxes

    Round pan, or “pancake,” options are shallow circular boxes that are most commonly used for ceiling- or wall-mounted light fixtures that weigh no more than 50 pounds.

    How do you install a surface mount electrical box?

    Installing the Surface Mount to an Electrical Box

    1. Install your gang box and pull the cables through the gang box.
    2. Remove the cable entry port on the back of the surface mount that the cables will use and pull the cables through.
    3. Install the surface mount to the gang box using the provided screws.

    How do you install pancakes?

    Quote from the video:
    Quote from Youtube video: So I put some backing up there and I'm ready to do my sheetrock patches. Okay now that I've run my electrical wiring for up here I'm ready to install. My little pant pancake box for the electrical.