How do you wire a swamp cooler motor and pump?
Quote from the video:
Quote from Youtube video: So we need to test that before we hook it all into our swamp cooler a way of testing that is to turn the switch to one of the settings that alienates uh each individual setting.
What is the orange wire on a swamp cooler motor?
Typically a red wire operates the motor’s low speed and is connected to terminal “1,” a black wire operates the motor’s high speed and is connected to terminal “C” and an orange wire operates the pump and is connected to terminal “2.”
How many wires does a swamp cooler need?
A two-speed motor will typically be prefitted with four short wires which must be connected to the swamp cooler control circuit and the 120-volt circuit. Solder all connections and use a shrink-wrap insulation kit to seal the connections.
What size is swamp cooler line?
Teeing Into a Plumbing Line
Rooftop evaporative coolers use more water than side-mounted units, so they are typically serviced by a 1/2-inch water line. This is the same size as all the other branch plumbing lines in the house, and you can use 1/2-inch copper, polybutylene, or PEX tubing for the cooler line.
How do you hook up a swamp cooler?
Quote from the video:
Quote from Youtube video: This one basically has a tap for the or a swamp cooler right there. And it just plugs straight onto a regular faucet.
How do you wire a swamp cooler thermostat?
Quote from the video:
Quote from Youtube video: Now the wires will get frayed away we'll show you that in just a little bit once we get started here go ahead and locate where you want to mount your swamp color thermostat.
What is the pump only switch for on a swamp cooler?
Swamp cooler controls will have an on/off switch that controls the water pump and fan hi/low button. When you turn it on it will begin pumping water through the cooler and then you can adjust the fan speed to high or low. You need to have the pump on while running the cooler, to keep water running through the unit.
Why does my swamp cooler only work on high?
A swamp cooler only works effectively when the water level is high enough to keep the internal pads damp. If the pads start to dry out, the swamp cooler may not work on the high setting.
Why would a swamp cooler stop working?
The most common reason for swamp coolers to break down is that the evaporative pads become saturated with water or that scale and debris builds up on them. It’s also possible that the internal belt will break or slip off, and in that case it will need to be replaced.
What are the parts of a swamp cooler?
The Parts of an Evaporative Cooler (Swamp Cooler)
- Motor.
- Shaft Bearings.
- Motor Pulley.
- Blower Pulley.
- V-Belt.
- Water Pump.
- Drain and Overflow Tube.
- Float Valve.
How do you connect a swamp cooler to a hose faucet?
Quote from the video:
Quote from Youtube video: Go ahead and slip our irrigation tubing. In go ahead and hand tighten the brass nut until it's hand tight and then we'll go ahead and take our wrench. And move it about a quarter of a. Turn.
How do you install copper tubing in a swamp cooler?
Quote from the video:
Quote from Youtube video: And also a compression ring and a compression nut we'll start first by sliding the compression nut atom to the copper. And then we'll also slide on the compression.
Why is my evaporative cooler leaking water?
The water may be dripping due to many reasons. Most often, it is due to improper storage of the cooling unit during the winter. Make sure that you store the unit properly. Before winterizing the evaporator cooler, you should drain the unit, remove the pads, and clean the tank.
How do I change the float on my evaporative cooler?
Instructions
- Open Up the Swamp Cooler. Remove the access panel on the side of the swamp cooler to gain access to the float valve and water line. …
- Disconnect the Water Supply Line. …
- Remove the Old Float Valve. …
- Install the New Float Valve. …
- Make Sure the Valve Works. …
- Adjust the Float.
How do I turn off the water to my swamp cooler?
Shut It Off – Don’t just turn it off. Unplug the power supply to make sure it doesn’t start up by accident in the winter. Cut Off Water Supply – Shutting off the water valve that leads to the evaporative cooler is the first step. We also recommend that you drain the hose that moves water in.
Can you run a swamp cooler without water?
A swamp cooler will still operate without water flowing to it, but this means it will run without lubrication, in turn causing irreversible damage to the pump from the friction.
How often should evaporative cooler dump water?
An evaporative cooler should dump water every six to 12 hours if it has a dump-style drain valve. It should also dump when it turns off. The minimum standard for dumping water is once every 24 hours.
Do swamp coolers need to be winterized?
While this equipment has few maintenance needs, keeping it operating efficiently requires an annual winterizing process. This helps prevent the water line from freezing and minimizes damage from condensation and rust. It also helps prevent heat loss through the cooler’s vent.
How do you prevent calcium build up in a swamp cooler?
You should clean the water pan reservoir at the bottom of the cooling unit at least once a month throughout the season to prevent minerals from building up inside. You should also wash the water curtains and filter every couple weeks with some mild detergent and lukewarm water.
What happens if you don’t winterize a swamp cooler?
Three main problems occur when you don’t winterize your evaporative cooler: Mold and Mildew Growth. Rust and Corrosion. Broken Water Pipes and Leaks.
