Questions about a broken vise

  • Can a broken vise still be used for something else, or should I throw it away?
  • Did I do something wrong, or was the vise bad quality? …
  • If it was my fault (i.e. even quality vises are breakabe): how do you know until which point it is safe to tighten a vise?

How do you fix a broken vice?

Quote from the video:
Quote from Youtube video: They put some screws. On this side and then they stick weld it I can see where they blew through in a couple spots. There stick weld actually. Worked here's what actually broke.

How do you weld a broken vice?





Quote from the video:
Quote from Youtube video: Bit i slightly warmed up the weld area with a map oxy. Torch. Final cleaning with a fine wire wheel then slowly laid down the root pass a half inch at a time peening with a punch between passes.

How do you restore a bench vise?

Quote from the video:
Quote from Youtube video: For all the smaller pieces I put them in a small container and soaked them in white vinegar to help loosen the rust.

Can you weld a vice?

Quote from the video:
Quote from Youtube video: And make it the same as the blue one but you more used to a fixed device and I hardly ever need to position this vise in any other direction. So I might as well just weld it.

How do you take apart a vice?

Quote from the video:
Quote from Youtube video: But if you had one that was in rough shape. And you needed to take it apart further to blast it or whatever you can see there's a screw right here and then this whole lead screw should come out.

How do you repair broken metal?





Quote from the video:
Quote from Youtube video: And more for bonding household metal surfaces together use jb weld quick bond for filling cracks or holes. Use our steel stick epoxy coating and for high heat repairs. Use high heat epoxy putty stick.

Can a cast iron vise be welded?

Quote from the video:
Quote from Youtube video: I constantly hear stories of guys taking their cast-iron parts to the local welding shop and being turned away as the welder says cast-iron cannot be welded.

How do you weld cast iron?

Quote from the video:
Quote from Youtube video: Difficult because the cast iron has to go through such an extreme temperature swing it's going from room temperature to welding temperature.

Can cast iron be repaired?

Yes, a cast iron skillet can be repaired. Depending on the damage it has encountered, you must choose a suitable method to repair it. Almost always, a good way to repair it is to use epoxy putty. In other cases, if possible you can fix it using a brazing torch or by using the cold stitching method.

Does welding melt metal?



As opposed to brazing and soldering, which do not melt the base metal, welding is a high heat process which melts the base material. Typically with the addition of a filler material.

Can cast iron be glued?

If you can get them to hold, switch to a type of glue that doesn’t require you to wet the surfaces. Steel-reinforced epoxy, commonly known as liquid weld, works on cast iron.

How do vices work?

A vice has two parallel jaws which work together to firmly clamp an object and hold it in place. One jaw is stationary, as it is attached to the fixed body section of the vice, while the other jaw is moveable.

What are the parts of bench vice?



Different Parts of a Bench Vise and Their Functions

  • The Base. The base of the vise is the part that holds everything together. …
  • The Jaw. This is where everything stays. …
  • The Slide. This part moves when the handle is turned, applying pressure to the object. …
  • Main Screw. …
  • Handle. …
  • The Anvil. …
  • Serrated Jaws. …
  • Pipe Jaws.


How do I clean a vice?

Use a wire brush and a sanding sponge to remove flaking paint, rust, and caked-on dirt. Vacuum off debris created by wire brushing. The last step is to soak a shop cloth with denatured alcohol and wipe everything clean. The cleaned parts are ready for masking tape.

How do you clean a rusted vice?

Quote from the video:
Quote from Youtube video: I use a screwdriver and a brass bristle brush to clean out all the.

How do you lubricate a vice?



Quote from the video:
Quote from Youtube video: Get a side shot of this. There we go that's what it looks. Like. So I slowly just beat it in the tolerances are kind of small on this vise. So you're really not gonna need a whole lot of grease.

Should you grease a vice?

Now a vice’s drive screw should really be greased, not simply oiled, and wax is not really an ideal replacement for grease on screw threads in regular use. But, we can see in the photograph that these are buttress threads, meaning this is a quick-release vice.