How do you remove a bathroom sink drain pipe from the wall?

Quote from the video:
Quote from Youtube video: So for this project we're just going to be loosening these two nuts that hold the J Bend and then also the nut that's holding the wall tube.

How do you replace a wall drain pipe?





Quote from the video:
Quote from Youtube video: Next i just glued the pipe into the no hub adapter which is already installed into the no hub coupling. Using some abs glue i followed the same procedure to install the sanitary. Tee.

How do you get rid of built up pipes?

Steps:

  1. Boil a pot of water.
  2. Pour a ½ cup of vinegar and a ½ cup of baking soda into the drain.
  3. Put cleaning rag over the top of the drain to cover it.
  4. Wait 5 minutes or so while the mixture eats away at the buildup.
  5. Remove rag and pour boiling water into the drain.

How do you replace elbow pipe under sink?

Quote from the video:
Quote from Youtube video: You can replace it fairly easily. Here's what you'll need to begin remove the old drain assembly from the top down. Use your pliers to unscrew any stubborn slip nuts.

How do you loosen PVC pipe under sink?

Quote from the video:
Quote from Youtube video: So you want to grip it just enough that you have a hold on it. Then I take my pair of pliers. And I'll grip the other one and just give it a little twist. And they should come right apart.

What is the pipe that comes out of the wall?





The plumbing vent, also known as a vent stack, helps regulate the air pressure in your plumbing system. Just as drain pipes remove water and waste from your home, the plumbing vent pipe – also known as a plumbing air vent – removes gas and odors.

How do you remove old drain pipes from walls?

Cut the PVC pipe at any point inside the wall that allows you to remove the stub-out, using a hacksaw. You may have to make two cuts to separate the tee holding the stub-out from the waste and vent pipes. Remove any clamps holding the stub-out with a screwdriver or hammer, and pull out the stub-out.

How do you remove a PVC drain pipe?

Heat can be used to soften and weaken the PVC. Direct heat onto the joint you are trying to break. Then, as the PVC heats, start pulling the connection apart. If you use heat to separate a pipe from a fitting, both the pipe and fitting should not be reused in pressure applications.

How do I remove glued PVC pipe?

Quote from the video:
Quote from Youtube video: There's also important to use a steel hole soft sand steel holds the heat very well. Okay after the time is up remove the hole saw. And use some needle nose pliers to pull out the softened pipe.

How do you remove an elbow pipe?



Quote from the video:
Quote from Youtube video: When you found the right one heat it thoroughly for around one minute and put it inside the pipe as such. What this does is it heats up the glue just enough for the pipe to unstick.

How do you replace elbow pipe?

Quote from the video:
Quote from Youtube video: Around here and break the glue loose which is good the other side right here is going to be a bit trickier because the glue is still making the seal i'll start prying this and cracking. It.

How do you remove a U bend under the sink?

Look under your sink and find the U-bend, it’s the first bend in the pipe immediately below the plughole. Put your bucket/dish under the U-bend and carefully unscrew the section of pipe. The U-bend has two sets of threads, one at either end. As you loosen them any backed up water will drain out, so take your time.

How do you replace PVC pipe under bathroom sink?



Quote from the video:
Quote from Youtube video: So the way this works is we'll have to cut this old one off the pipe. This will get cemented on and then the p-trap tube will just fit right in there into that slip. Fit.

How do you remove PVC cleanout plug under sink?

Use an adjustable wrench or adjustable pliers to unscrew the clean-out plug from a P-trap. Place a bucket under the trap to catch the water that will spill out when you remove the plug. Turn the plug counterclockwise to remove it, install the replacement, and turn it clockwise to tighten it.

How do you remove a P-trap from the wall?

To remove the P-trap from the wall stub, hold the trap assembly firm with one hand and turn the coupling nut counterclockwise with respect to the wall stub until it comes loose. If the nut is overtightened or old, you might have to use a wrench or a pair of pliers for the purpose.

Where is the P-trap located on a bathroom sink?

Quote from the video:
Quote from Youtube video: All right today we're gonna look at how to fix a clogged sink. It's pretty simple first thing we're gonna look at is the p-trap or p stop which is right underneath your sink.

What to do if P-trap is glued?



Cut two sections of PVC pipe (5 inches or longer) that are the same diameter as the existing pipe. Remove burrs. Apply PVC primer to one outside end of both pipes and the inside ends of a new P-trap. Apply PVC cement to all primed areas and push the cemented pipe ends into the ends of the P-trap.

Where is the P-trap in bathroom sink?

Related Articles. The P-trap is a U-shaped pipe immediately under the bathroom sink that connects the sink drain to the drain outlet in the bathroom wall.

Does P-trap have to be directly below sink drain?

You attach the p-trap directly to the drainage and manuever the p-traps exits into you existing drain. It is not ideal to have the p-trap below the the exit drain because water gravity has to force the water out instead of it flowing downwards naturally. They both work and have seen it many times.

How do you extend a drain pipe from a wall?

Quote from the video:
Quote from Youtube video: So you need the proper washer insert the retention nut. And the nylon washer. And loosen up there p-trap. And install the extension tail piece. And stole another retention nut.