How do you reset the code on a Rheem furnace?

8 Steps to Reset Your Rheem Furnace

  1. Check to see if the pilot light is off. …
  2. Set the thermostat to the lowest possible setting. …
  3. Switch off the power. …
  4. Close the gas supply to the furnace. …
  5. Reignite the pilot light with a matchstick or lighter. …
  6. Turn on the power and the gas supply. …
  7. Press the reset button and hold for 30 seconds.

How do you read a Rheem furnace error code?





Quote from the video:
Quote from Youtube video: Many other furnaces Rheem ones don't use flashing LED light sequences to indicate errors and the display will instead give you a simple code you can use for Diagnostics.

What causes high limit switch open?

Airflow issues usually cause a high limit switch to trip out. With less airflow going through your furnace, the heat exchanger excessively heats up and causes the limit switch to trip. Airflow issues can be caused by many different things such as: Dirty air filter.

Where is the reset button on a Rheem furnace?

Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.

Where is the blower motor reset button?

Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.

How many times can I hit the reset button on my furnace?





twice

Don’t hit “reset” more than twice. The process pumps oil into the burner chamber, where it can accumulate if you have no ignition. Then when the furnace finally does start, it can do so explosively. So if the button won’t reset, or quickly pops up again, it’s time to call a professional repair service.

How do you troubleshoot a Rheem furnace?

Quote from the video:
Quote from Youtube video: Power go to your circuit board and make sure the fuses aren't cracked or blown. If it's blown replace it but otherwise resetting the circuit should help if none of the above.

How do you read a furnace code?

Although furnace error codes differ between brands, all the most popular furnace brands use a system of blinking lights to communicate error codes. To read a furnace error code, locate the LED light and note its blinking pattern. Be sure to count how many times the light flashes and to note how quickly it’s blinking.

What does 3 blinks mean on a Rheem furnace?



Three LED blinks with a two-second pause indicates the limit switch is closed. A limit switch is a safety feature directly wired into the furnace; it stops a furnace from overheating if air isn’t properly flowing through the heat exchanger.

Where is the reset button located?

Alternatively referred to as the reset switch, the reset button allows devices that utilize it, such as a computer or peripheral to be rebooted. Usually, the button is on the front of the device, next to or near the power button.

What is the limit switch on a furnace?

A furnace limit switch is a component of a forced-air furnace that is responsible for turning on the furnace blower once the desired heat has been met inside the furnace. Without a functioning furnace limit switch, a furnace would not be able to regulate the temperature in conjunction with a thermostat.

Why is my Rheem furnace keeps shutting off?



If your furnace keeps shutting off, it could be due to low airflow. There are several indirect issues that cause low airflow. Dirty Air Filters. If you don’t change your air filters often enough, the filters will become dirty and clogged, which means the heat exchanger retains heat and eventually causes it to overheat.

How do I reset my blower fan?

How to Find and Reset your Furnace Motor Blower

  1. Step 1: Turn off the power to the furnace. …
  2. Step 2: Remove the blower compartment cover. …
  3. Step 3: Make sure the blower is completely cooled off. …
  4. Step 4: Locate the reset button. …
  5. Step 5: Press the button in (assuming that this is your issue and that the button has popped).


What would cause a furnace blower not to kick on?

Make sure that the power cord hasn’t melted or a fuse hasn’t been blown. If your cables are looking fine, try unplugging the fan for a few minutes and then plugging it back in again. Sometimes, this process can reset the motor and solve your furnace problems.

How do I know if my blower motor resistor is bad?



If you try to increase the air pressure and you feel no difference in the pressure blowing, then your blower motor resistor may be failing. A damaged blower motor resistor will work on one fan speed which may not be enough to keep the inside of your car cool or warm enough.

How much does it cost to replace blower motor resistor?

The Best in Auto Repair



The average cost for blower motor resistor replacement is between $112 and $143. Labor costs are estimated between $44 and $55 while parts are priced between $68 and $88. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location.

Where is the blower resistor located?

The blower motor resistor is usually extremely easy to access, but the hard part can be positioning your body inside the car to remove the part. The resistor is at the bottom of the HVAC housing or just behind the glove compartment.

What happens when a blower motor resistor fails?

If the resistor shorts or fails, it may cause the blower motor to remain stuck on one fan speed. The heating and air conditioning systems may still function at one speed, however the resistor will have to be replaced in order for full functionality to be restored.

How do I test a blower motor resistor?



Place one lead of the Ohmmeter on terminal 1 of the resistor. Place the other lead on terminal 2 and check against specifications. If this circuit is open, showing infinity on the Ohmmeter, the blower resistor must be replaced. Move the lead from terminal 2 to terminal 3 and check this reading against specifications.