Slide Over Bolts Method

  1. Locate the studs behind the brick, stone, or faux veneer.
  2. Drive 1/2in lag screws through each of the studs. …
  3. Have a helper support the mantel while you mark the location of the support rods on the back of the beam. …
  4. Apply construction adhesive into the holes. …
  5. Slide into place, admire, and enjoy!

How do you hang a heavy barn beam mantel?

Quote from the video:
Quote from Youtube video: Basically took a five and a half foot board ripped it at an angle. And then tap conned it to the concrete wall these tap cons like I said earlier about four inches long.

How do you hang a heavy beam mantel?





Quote from the video:
Quote from Youtube video: Alright so to mount the mantle. I use sleeves. And lag bolts. It's quite neat you want to make sure that your sleeves are mounted in the center of bricks.

How do you turn a barn beam into a mantel?

Quote from the video:
Quote from Youtube video: The first coat i put on pure varnish. Make it nice and thick. And then get off any of the dust. Then i'll come back through with a tacky cloth. And clean out.

How do you secure a floating mantel?

Remove the old mantel. Add support by drilling holes for lag shields, then install lag bolts into the brick. Measure carefully and drill corresponding holes for the wood mantel. Push the wooden mantel carefully into place using wood glue for extra support.

How do you mount a barnwood mantel?

Slide Over Bolts Method

  1. Locate the studs behind the brick, stone, or faux veneer.
  2. Drive 1/2in lag screws through each of the studs. …
  3. Have a helper support the mantel while you mark the location of the support rods on the back of the beam. …
  4. Apply construction adhesive into the holes. …
  5. Slide into place, admire, and enjoy!





How do you secure a wood beam mantel?

Mark where the bolts would be inserted and drill holes in your mantel where the bolts will slide in. Apply construction adhesive to the inside of the mantel holes and to the back of the mantel if it will be able to stick to the surface. Slide it into place and ensure the glue is holding in place.

How do you make a mantel cleat?

Quote from the video:
Quote from Youtube video: Together a little bit so that this piece fits better all right so i went overkill with the glue most of it's going to go on the inside where you can't see it. So yeah we'll get this cap.

How do you fit floating oak beams?

Quote from the video:
Quote from Youtube video: But this time draw a level line on the wall no bigger than the mantel you're fitting mark whether Center Point is measure. The distance between the fixing points on the back of the mantel.

How do you attach a mantel to drywall?



Quote from the video:
Quote from Youtube video: You can hang the cleat from these drywall anchors. So now we're ready to hook the mantle onto the cleat. So what we have here on the inside of the mantle.

How do you install a wooden mantel?

Quote from the video:
Quote from Youtube video: If you look at the top of the mantel there's some pre-drilled holes that the fabricator put there for us to put these screws. Into. It's completely Center so let me hold this in place.

How do you install oak beam mantel?

Quote from the video:
Quote from Youtube video: Using the 10 millimeter masonry drill bit drill a 70 millimeter deeper hole where you've marked for the brackets to be installed in the wall. Keeping. The drill straight and level as you do.

How high should a mantle be above the floor?



Mantel Height: We recommend installing the mantel 4.5′ from the floor. This allows room for stockings during the holidays. Most housing codes and the National Fire Protection Agency (NFPA) state that the bottom of the mantel must be at least 12” away from the top of the fireplace box.

How much weight can a mantle hold?

The maximum weight for all 60INCH MANTELS is 150 lbs. The maximum load for all 72 inch mantels is 180 lbs.

How far should a mantle stick out?

A mantel should stick out at least 6 inches (15.24cm) from the wall. It’s the perfect depth that allows you to have a mantle effectively deflect heat without compromising aesthetics. You can extend it to have more depth for your decorative pieces, but we don’t recommend having it less than 6 inches (15.24cm).

How do I protect my wood mantel from heat?

A heat deflector is installed to provide air space between it and the wood mantel, and it’s bent at a 45 degree angle to deflect heat away from the mantel. It turned out great! It does its important job and is barely noticeable.

Are wood mantels safe?



Building Code & Clearance Information – Fireplaces Designed to Burn Wood. Warning: Risk of fire and/or smoke damage may occur as a result of fireplaces and mantels installed without adequate fire-hazard clearances and may lead to asphyxiation, injury and/or death.

How do you heat proof a mantle?

A mantle heat shield can be used to protect mantles from excessive heat and be used to protect TV’s and sound bars from heat damage. Mantle heat shield can be used to protect fireplace mantles from excessive heat and damage. They may also be used to shield TV’s and sound bars located above a fireplace.