What can I use for a sill plate?
Sill Plate is a tough, versatile pressure-treated lumber. Like borate-treated lumber, it’s guaranteed to stop termites and prevent decay, plus it’s compatible with carbon steel (black iron) fasteners. But unlike borate-treated lumber, it requires no special handling.
What can you use instead of pressure treated wood?
There are many safer alternatives to pressure-treated lumber for raised beds, including: raw lumber (pine, douglas fir), composite timber, recycled plastics, logs, rock, brick, concrete blocks, steel, and stone.
What should I put between wood and concrete?
Anyplace where wood meets the ground or concrete, the lumber must be pressure treated. For additional moisture protection, a gasket or strip of closed-cell foam can be installed between the concrete foundation and the sill plate.
Do I need pressure treated bottom plate?
Pressure-treated bottom plates deal with the symptoms of the problem when a capillary break between wood and concrete deals with the cause. No direct contact, no need for pressure-treated bottom plates. A cautionary note about moisture meters and pressure-treated wood.
What is the difference between a sole plate and a sill plate?
The sole plate, also sometimes referred to as the sill plate, the mud sill, or the base plate, is the main supporting beam of a wall in the construction industry. Typically, these are the first piece of wood that is in contact with the masonry of the basement or foundation.
What type of wood is used for bottom plates?
In single and multi-family housing when a stud wall is placed on top of a subfloor or other wood substrate, a bottom plate is typically some version of a stress-graded dimensional lumber, either 2×4 or 2×6 in most cases, but occasionally greater if necessary.
Can I use non pressure treated wood for deck railing?
Yes, you can use untreated wood to build a deck, but not without preparing it first. You can’t, of course, pressure treat it yourself, but you will need to seal; the wood and stain/paint it to ensure the wood is ready to take on the harsh external weather.
Can you cover pressure treated wood with PVC?
A. Yes, you can install PVC riser and trim boards directly over unprimed pressure-treated wood.
Is it safe to use pressure-treated lumber for a raised vegetable garden?
Modern Pressure-Treated Lumber
According to the American Wood Protection Association and the U.S. Environmental Protection Agency, lumber treated with ACQ is safe for garden use. Its durability and nontoxicity make it among the best woods for raised garden beds.
Can you use untreated wood on concrete?
Quote from the video:
Quote from Youtube video: Or you do use the the wood anyway I would still recommend a vapor barrier. As. Far as underneath the concrete. Anyway for having the vapor barrier weather.
How do you keep water from going under a sill plate?
A filler, similar to caulk, is generally used to seal these gaps between the sill plate and foundation when the home is constructed. Over time it can crack and chip, allowing water to seep — or even pour — into the basement.
Should pressure treated wood be used for basement framing?
Basement Masonry Walls
Pressure-treated wood is required whenever you attach framing lumber or furring strips directly to concrete or other exterior masonry walls below grade. Note that this requirement is only for exterior walls, as these may wick moisture onto the lumber.
What size wood is used for sill plate?
A sill plate, also known as a sole plate, is the bottom horizontal part of a wall or building to which the vertical studs will be attached. Most sill plates are made from lumber – usually measuring 2″ x 4″, 2″ x 6″, 2″ x 8″ or 2″ x10″.
How thick should a sill plate be?
2 inches
3.1 Bottom Plate or Sill. Studs shall have full bearing on a plate or sill. Plates or sills shall be not less than 2 inches (51 mm) nominal in thickness and have a width not less than the width of the wall studs.
How do you seal between foundation and sill plate?
Caulk and, or spray foam can be applied at the seam where the sill plate sits on the foundation, and it can be used to seal (and insulate when spray foam is used) the area where the subfloor and rim joist sit on the sill plate. Any penetrations through exterior walls must be sealed.
Is sill seal necessary?
Quote from the video:
Quote from Youtube video: These gaps can allow uninvited guests as well as airborne contaminants into your home. We've all heard walls popping as walls flex with weather and temperature.
Should I insulate my sill plate?
It is important to also seal and insulate the top of the concrete wall where the sill plate sits. It’s the simplest and least expensive basement area to insulate, and will bring the highest return on your investment.
How do you seal a gap between concrete and wood?
How to Water Proof Between Wood & Cement
- Load a tube of caulk into a caulking gun. …
- Cut the end of the caulk tube off with a utility knife to accommodate the size of the gap between the wood and the cement. …
- Fill the gap between the wood and the cement with backer rod if needed.
What can I use to cover a wood foundation?
Gypsum board or wood paneling can be nailed or glued directly to the foundation studs without the need for furring strips.
Can wood touch concrete?
Wood in direct contact with concrete, and the dampness often found there, will rapidly decay. To avoid this, use pressure-treated lumber. This is wood impregnated with decay-resisting chemicals, usually chromated copper arsenates.
27 мар. 1988
