Solutions for a difficult-to-reach shut-off valve
- Create a second way to access the valve in the floor directly above it. …
- Remove the valve and insert some elbows and additional tubing so that it could be relocated right inside the existing crawlspace access hatch.
How do you remove a stubborn shut-off valve?
Quote from the video:
Quote from Youtube video: Then you want to remove the valve by holding the body with one wrench and undoing the nut with another.
How do you replace a water shut off without turning off water?
Quote from the video:
Quote from Youtube video: Clean cutter and just slip want to be sharkbite son. With the water and shut up. And shop back all the remaining water around the perimeter. And you're good to go.
Can you move a water shut-off valve?
In addition to moving the water shut-off valve, we recommend replacing the standard valve with a ball valve. A standard valve requires multiple turns and runs the risk of the stem breaking. A ball valve that only takes a quarter turn and is less likely to break.
Can you spray WD40 on water shut-off valve?
Absolutely – WD40 is safe for use on plumbing. So, if you have a stuck water shut-off valve, consider using WD40 to loosen things up. Many folks, especially avid DIYers, have WD40 on hand, so it might save you a trip to the store. WD40 is a non-lethal solution that won’t damage or dissolve the pipe or the threads.
How do you fix a seized water shut off?
If this doesn’t work and the shutoff valve remains fixed in place, try heating the valve with a hair dryer. Spray down the valve again with the penetrating oil, and then try again with the wrench. Doing this over and over again, you should be able to loosen your stuck valve.
How do you loosen a tight tap valve?
Try tapping the body of the valve with the handle of a wench or adjustable spanner while you turn the valve will do the job. Warm up the body of the valve with a hair dryer, or (carefully) with a blowtorch might expand the body of the valve enough to allow the gate (or other moving parts) to move more freely.
Can a sharkbite valve be used for main water shut off?
Shark bite valve will be fine. Just make sure you clean the copper pipe thoroughly so there are no rough edges or bits of solder left.
Can I change a tap without turning the water off?
The simplest way to do this is to turn off the supply to each tap in turn and check which stops the drip. Mixer units may also have a separate ‘o-ring’ seal at the base of the spout. This can be replaced without turning off the water supply, but make sure you get the correct size replacement before starting work.
How do I shut off the water to my house without a tool?
Quote from the video:
Quote from Youtube video: Without special tools put a screwdriver into the hole of this wrench adjust the opening of the wrench to fit the valve. You can turn the screwdriver.
How do I remove a rusted water shut off valve?
Quote from the video:
Quote from Youtube video: To take this valve off you need to hold one wrench on the nut itself and another wrench on the valve. And turn them against each other until you get it to release. And then just unscrew.
How do I remove a corroded water valve?
How to Loosen a Corroded Water Valve (Step-by-Step)
- Shut Off Your Home’s Primary Water Supply.
- Turn On Faucets Throughout Your Home.
- Use a Cloth To Wipe Away Dirt and Grime.
- Apply Penetrating Oil to the Valve.
- Use a Hairdryer To Heat the Valve.
- Use Your Wrench To Twist the Valve Again.
- Replace the Valve if Necessary.
Can you lubricate a PVC ball valve?
The ball and handle might require lubrication if the valve becomes difficult to turn. It’s easiest to lubricate the ball valve before gluing it to the connecting PVC pipes, but you can still lubricate it even after installation.
How do you lubricate a valve?
Quote from the video:
Quote from Youtube video: The valve about two-thirds of the way will allow the oil to sufficiently coat the piston. When you apply the oil you need only apply a few drops on each side of the valve three to four at most too.
Do ball valves need lubrication?
Ball valves are not very high maintenance parts. Other than worn O rings that seal the ball inside the valve body, keeping the valve clean and free-turning with a little lubrication is all it needs. It’s when a valve looses its lubrication and debris or corrosion builds up that it can become hard to turn.
Are PVC ball valves reliable?
Ball valves are durable, reliable and securely shut off flow even after sitting idle for long periods of time. Because of this, they are frequently used as fluid and gas flow cut-off valves.
Are brass valves better than plastic?
Higher Pressure Rating — Brass has a higher tensile strength and more elasticity than plastic which make it more resistant to bursting. Higher Chemical Resistance — Brass is more resistant to chemicals typically found in irrigation water and therefore less susceptible to failure due to cracking.
How long do PVC ball valves last?
about eight to ten years
A ball valve is a shut-off valve capable of preventing or allowing liquid or gas to pass through a fixture. Using the latest and greatest ball valve in your plumbing can help save more water. It also helps you save money while helping the environment. A ball valve life expectancy is about eight to ten years.
