What is the trim on stairs called?

A stair skirt or baseboard is the trim that runs along the bottom of the wall beside the steps. Often, it is made from the same baseboard used throughout the home, but it can also have a different appearance entirely. Baseboard trim can be cut with mitered corners and follow the angles of each tread and riser.

How do you trim a staircase?





Quote from the video:
Quote from Youtube video: Given. This skirt board was notched over here that way it could stay on the same plane. Continue around with the one by six pinch dog biscuits.

Do stairs have trim?

A stair skirt board is an unbroken piece of trim for your stairs. If you have stairs with a closed-end – against a wall – then you more than likely have a stair skirt board. Stairs with two closed ends will have a stair skirt board on both walls.

Do baseboards go on stairs?

Installing baseboards anywhere can be tricky, but many people struggle most with installing baseboards around stairs. While doing baseboards around stairs requires planning, measuring, and a bit of elbow grease, it can be easily done in just a few steps!

What are stair supports called?

Balusters – Also called spindles or stair sticks, are the vertical posts that support the rail.

What are the sides of stairs called?





The landing of a staircase is either a platform where the direction of the staircase changes or is located at the top of a staircase. The outer string is the side of a staircase where the treads and risers can be seen from the side. A riser is a vertical board that forms the face of a step.

What is a stair skirt?

A stair skirtboard is a continuous piece of trim or molding for the sides of your stairs to give them a finished look. There are two kinds of skirt boards for stairs. The first type is the one between the stairs and the wall adjoining the stairs.

What is a stair Cove?

Cove moulding (also spelled as “cove mold”) is a small decorative profile used underneath the bullnose of a stair tread against the top of the riser. Cove mould is typically installed in the same species as stair treads.

How do you install wainscoting on stairs?

Quote from the video:
Quote from Youtube video: One of the best ways of dealing with the bottom rail of staircase wainscoting is by building the stairs with a gap between the ends of the rough treads. And risers and the wall.

What is shoe molding?



Paired with a baseboard and painted to match, shoe moulding (also called “base shoe”) is a thin strip of moulding that finishes out the look of baseboards. It can often be found in a curved or round shape similar to quarter round moulding.

How do you change baseboards to stairs?

Quote from the video:
Quote from Youtube video: And then also acts as a support to the upper two pieces of baseboard that will go on top at the bottom of course.

How do you finish carpet edges on stairs?

How to Finish the Side of a Carpet on Stairs

  1. Measure and Cut Your Carpet and Padding. …
  2. Measure and Cut Tackless Strips. …
  3. Add Extra Strips Where Needed. …
  4. Install the Padding. …
  5. Install the Carpet. …
  6. Measure the Width of the Stair Tread. …
  7. Install Tack Strips and Padding. …
  8. Cut Your Carpet Pieces.

Can you staple carpet to stairs?



Stapling plays several important roles in the process of carpeting stairs. The most secure anchors for carpet top and bottom, staples also hold padding tightly to stair treads. In traditional “cap-and-band” carpet installation, staples secure carpet pieces at the edges of stair treads and along the risers.

Can you install carpet on stairs without tack strips?

Install Carpet Without Tack Strips



Small tension rods attached at the base of each stair can be placed to tighten carpet that runs the entire length of the stairs. A small amount of glue at the top and base of each stair can keep it in place. Another option is to carpet each stair individually where the foot lands.

What to do with stairs after removing carpet?

Hardwood Stairs Refinishing Process

  1. Remove any carpeting from the stairs.
  2. Remove all carpet staples.
  3. Strip the stain from the treads.
  4. Sand the treads and risers using an orbital hand sander.
  5. Hand sand the spindles, banister and around the base of the spindles.
  6. Vacuum and wipe down everything until the dust is gone entirely.

Is it better to have carpet or wood on stairs?

Carpet is the Safer Choice



If you’ve got small children or elderly members of your family using the stairs often then carpeted stairs is recommended. Hardwood floors can become dangerous if there is anything spilled on them. If you do trip or fall, hardwood will cause more injury than carpet.

How do you transition from carpet stairs to wood?



Replacing Carpet on Stairs With Hardwood

  1. Step 1: Remove the Carpet. …
  2. Step 2: Remove Staples, Nails or Tack Strips. …
  3. Step 3: Cut Existing Nosing. …
  4. Step 4: Measure the Stairs. …
  5. Step 5: Cut Riser Pieces. …
  6. Step 6: Cut Tread Caps. …
  7. Step 7: Attach Edge Moulding. …
  8. Step 8: Measure the Tread Size.

Is there an alternative to stair carpet?

Laminate flooring is among one of the most popular alternatives to carpet on stairs for many reasons. Laminate floors are notably less expensive than other carpet alternatives and offer a brilliantly affordable alternative to expensive carpeting.

Do stairs have to match floors?

Stairs can be darker than the floor, but they do not have to be. As long as your stairs complement your floors, you can make them any color you wish.

Are wooden stairs slippery?

While wood flooring on your stairs can provide a sleek and modern feel to your home, they can also be dangerous. Wood stairs can be slippery, and there’s not much cushion if a fall were to happen. If you have children, seniors or sleepwalkers in your home, wood stairs may not be the best choice in terms of safety.