Where does the condenser wire go?
The condenser may be fitted outside the distributor, or inside on the contact-breaker baseplate; on a few cars it is fitted into the wiring somewhere near the distributor.
How do you wire a thermostat wire to a condenser?
Quote from the video:
Quote from Youtube video: Inside the furnace you see that we have a W and R a Y a G and a C and so those are located on the control board inside the furnace the terminals for the thermostat or W. That's for heat Y.
Why does my thermostat have 2 wires?
The most basic thermostat has 2 wires; usually a red and a white wire. Two wire thermostat wiring is used for furnaces only and usually doesn’t need a “C” or “Common” wire. That’s why we only need two wires: Red wire for power (24h).
How do you wire a 2 wire thermostat?
Quote from the video:
Quote from Youtube video: One on the top. And there's one on the bottom. It's gonna allow us to remove the plate from the wall. And then we have our two wires our black wire and our white wire in my case.
Does the condenser go on the positive or negative?
Having a condenser on the positive side of the ignition will not do much. It may suppress some RFI when listening to some channels on the AM radio, but having a condenser on the negative side of the coil would do a better job of suppressing noise while also protecting your points.
Why is there a condenser on my coil?
The condenser absorbs the energy and prevents arcing between the points each time they open. This condenser also aids in the rapid collapse of the magnetic field.
What happens if you wire a thermostat wrong?
Potential consequences of improper installation could include: Electric shock. Blowing a circuit breaker. Damaging the thermostat unit, the electrical system or even the AC/furnace unit itself.
What color wire goes where on a thermostat?
This is the most typical thermostat wiring style, and it applies to systems that regulate both heat and air conditioning. The wires are typically arranged as follows: red for 24-volt hot, white for heat, yellow for cooling, green for the fan, and blue for common (although the common wire may be a different color).
How do you wire a thermostat for AC?
Quote from the video:
Quote from Youtube video: This right here is a piece of thermostat wire I just cut a piece off. And you strip both ends off and you get yourself a little jumper.
How does a two wire thermostat work?
A basic two-wire thermostat can be compared to a simple single-pole switch that you will find throughout your home, only instead of you turning the switch on and off as required, a mechanical or electronic temperature controlled mechanism is the operator of the switch. The terminals are usually marked ‘R’ and ‘W’.
How do you read a thermostat wiring diagram?
Quote from the video:
Quote from Youtube video: And it's going to look like this whenever you see a switch like this on a wiring diagram that is a temperature switch which means this switch goes up and down depending on the temperature.
What is Y2 wire on thermostat?
The Y2 Wire on a Thermostat controls your cooling system and should be connected to the Y terminal on the Thermostat. If your HVAC system has two-stage cooling, there’ll be two Y terminals on your Thermostat to control two compressors.
Does a condenser need to be grounded?
Your outdoor condenser unit must be grounded to meet most local codes. The copper ground wire should be connected to the ground terminal block, which is mounted to the metal panel. The wire is then held in place with a tightened screw.
Should coil have power both sides?
Yes, if the points are open and/or the electronic module is NOT CLOSED then you will measure battery voltage on both the coil (+) and coil(-) terminals. Since there is no current flowing through the coil (no path to earth) then both sides of the coil will be at the same potential.
Is condenser needed with electronic ignition?
Electronic ignition does away with the need for a traditional condenser and points, so these need to be removed by unscrewing them from the distributor base-plate.
What is the purpose of a capacitor in an ignition system?
A Capacitor Discharge Ignition or CDI is an electronic ignition device that stores an electrical charge and then discharges it through an ignition coil in order to produce a powerful spark from the spark plugs in a petrol engine. Here the ignition is provided by the capacitor charge.
What happens if the condenser is removed from the booster coil circuit?
Without a condenser, an arc would jump across the points with each collapse of the magnetic field. This would burn and pit the contact points and greatly reduce the voltage output of the booster coil.
What does an electrical condenser do?
A capacitor (originally known as a condenser) is a passive two-terminal electrical component used to store energy electrostatically in an electric field. The forms of practical capacitors vary widely, but all contain at least two electrical conductors (plates) separated by a dielectric (i.e., insulator).
Is condenser and capacitor the same thing?
Condensers work as heat capacitors, so they store energy in the electrostatic field. On the contrary, capacitors store energy in the electric field. More commonly a condenser refers to an apparatus that transforms a gaseous substance to its fluid state.
What is a voltage condenser?
Capacitor vs. Condenser : Comparison chart
| Capacitor | Condenser |
|---|---|
| Commonly used term for two conductive surfaces separated by insulating material | Rarely used term |
| The energy that is surrendered to the element turns into an electric field | The energy is turned into electrostatic field |
