What do you do with extra wires on a light switch?
Quote from the video:
Quote from Youtube video: Together i screw them together or twist them together with clients pliers then i take a wire nut make them nice secure.
How do you wire a ceiling fan with a light dimmer switch?
Connect the incoming red as live wire to the single way switch. The other end of the SPST switch should be connected to the combine dimmer and speed regulator switch. Now connect the upper left end of the regulator switch to the red wire of fan and connect the upper right end of the dimmer to the blue wire of light.
Why does my dimmer switch have 4 wires?
Since the switch cuts the power on and off, there will be a black wire coming into the switch and a black wire leaving. The whites are normally just connected together with a wire nut and the coppers are connected together with a wire nut or grounded to a metal junction box. So the new switch has four wires.
Do you need special wiring for a dimmer switch?
New dimmers have either a green grounding wire or a green ground screw that you’ll have to connect to a grounding source if one is available. Houses wired with plastic-sheathed cable almost always have bare copper ground wires that you’ll connect to the toggle dimmer switch.
Why is there two black wires in light switch?
You should see two black wires, each connecting to a different screw on the side of the switch. These are called terminal screws. You will also see two white (neutral) wires that connect to one another in the box.
How do you wire a switch with two black wires?
Connect the top screw to the wire that feeds to the light. Connect the bottom screw to the hot wire. When you turn the power back on, and if you want to swap the direction of the switch (as in press down to turn off, or turn on), turn off the power and switch the two black wires.
Can you put a dimmer switch on a ceiling fan with a light?
Standard dimmer switches should never be used to control the fan motor on a ceiling fan because the dimmer could damage the fan motor, or overheat and start a fire.
Can you put a dimmer switch on ceiling fan?
A dimmer switch can theoretically control a ceiling fan. However, standard dimmer switches shouldn’t be used to control ceiling fans because they can easily overheat and cause a fire. They can also damage the ceiling fan motor. To avoid these issues, use a dimmer switch specifically designed for ceiling fans.
How do I make my ceiling fan light dimmable?
Many ceiling fan and light combinations are built to operate the fan separately from the light and to use them at different speeds and levels of brightness. To use it that way, you need to install a three-way dimmer switch for ceiling fans with individual controls for the fan and light switch.
What are the 3 wires on a dimmer switch?
Single pole switches will have 3 wires: a hot lead wire, a ground wire, and a traveler wire. Older homes may only have a hot lead and a ground wire. If you have less than three wires, stop and call an electrician.
How many wires do I need for a dimmer switch?
There will be three wires: one black, one white, and a separate ground wire that may be bare copper or is sometimes wrapped in green. Identify the different colored wires, and use needle-nose pliers to attach the wires to the dimmer in the same way they had been attached to the switch (Image 1).
Is a dimmer switch wired the same as a normal switch?
Replacing a standard single-pole or three-way switch with a dimmer switch is no different than replacing a standard switch. Remember: Dimmer switches don’t work on most fluorescent fixtures, and low-voltage lighting requires special low-voltage dimmers.
How do you hook up a dimmer switch?
Connect the New Dimmer Switch
Connect the ground wire from your dimmer to a green or bare copper wire in the wall box. Twist the ends together clockwise and cap them using a wire connector nut. Connect each dimmer wire to a house wire by gripping the wire ends with a pair of pliers and twisting them together.
Can you swap a dimmer switch with a regular switch?
Disconnect the traveler and/or common wires from the dimmer switch. Loosen the screw that holds the grounding wire to the switch and remove the dimmer switch from the switch box. Next, using a pair of needle-nose pliers, wrap the bare ground wire around the green screw at the bottom of the new standard switch.
Why are my dimmable lights not dimming?
One of the most apparent reasons for dimmer switches not being able to dim all the way is the lack of compatibility between the dimmer and bulb you have used. There are dimmable bulbs and non-dimmable bulbs; if you were to use a non-dimmable bulb with a dimmer switch, it wouldn’t work out at all.
Why would a dimmer switch not work?
If your dimmer switch suddenly stops working, there could be issues with the electrical wiring. If it’s not installed correctly or the wires come loose, the switch might stop working. You might hear a buzzing or crackling sound if wiring is the issue. When you suspect a wiring issue, hire an electrician to inspect it.
How do you fix a dimmer switch that doesn’t dim?
Steps on fixing a dimmer switch that turns on but does not dim
- Step 1: Install your dimmer correctly.
- Step 2: Check whether your bulb is compatible.
- Step 3: Confirm that your dimmer is not faulty.
- Step 4: Check whether it’s time to replace your dimmer.
- Step 5: Ensure the dimmer you are using is correct.
Is there a fuse in a dimmer switch?
So, are there fuses in dimmer switches? Older dimmer switches did have fuses to protect the switch or prevent dangerous temperatures if the switch got too hot. Unlike most fuses, they were integrated and difficult to replace. Modern dimmers have generally stopped using fuses.
How do you tell if a dimmer switch is broken?
Attach the continuity tester’s alligator clip to one of the dimmer wire leads. Hold the continuity tester’s probe to the other dimmer wire lead. If the continuity tester’s continuity LED glows, the device is working; otherwise, you have a faulty dimmer switch.
How do you reset a dimmer light switch?
Press and hold button 6 for 10 seconds until LED blinks red. The LED should change to solid purple after the reset is complete. Note: A reset must be performed on each Dimmer Switch in 3- and 4-way configurations. Wait 5 seconds after the reset before putting the Dimmer Switch into pairing mode.
