How do you run a gutter from the upper roof to a lower roof?
Quote from the video:
Quote from Youtube video: And ran the downspout all the way across the roof dropping into the lower eaves trough. Which will save the shingles over time unfortunately these ones are worn so much they will need a repair.
How do you reroute a gutter downspout?
Redirecting roof runoff is as simple as adding a downspout extension. These are plastic (PVC) or metal extensions that attach to the bottom of your existing downspout. The extension should carry your roof runoff at least three to five feet away from your home to prevent any water damage to your home or foundation.
How do you connect two gutter downspouts?
Quote from the video:
Quote from Youtube video: Makes it a little bit easier to fit these pieces. And do once one pinch on each corner. Now once that's done here's the UNCHR impt end the crimped end you can see is a little bit smaller.
What is a downspout scupper?
Description: Scuppers are used to provide an outlet through parapet walls or gravel stops on flat and built-up roofs to allow drainage of excess water. They can be used in conjunction with gutters and downspouts to divert the flow to the desired location.
Should a downspout empty on to roof?
A hole at the bottom of the gutter or an open gutter end will just splash water around in a heavy rain. It is also not a good idea to drain down a lower roof too close to adjacent wall above the roof. Then there is the aesthetic consideration.
Should gutters empty onto roof?
A gutter trough should be installed along the edge of every roofline, with a downspout to drain away the collected water. A downspout from an upper roof should drain into a lower gutter. It should never drain directly onto the roof, as this will cause premature deterioration of the shingles and roof deck.
Where can I divert downspouts?
Quote from the video:
Quote from Youtube video: If you need underground drainage stealth flow also can be buried beneath flat surfaces. Like sidewalks or driveways. And works well when transitioning from above-ground drainage to buried drainage.
Can you change direction of downspout?
Over time, things may change and you may find it necessary to change the direction of the downspout. Redirecting any downspout can be accomplished in just a few minutes.
Can downspouts be moved?
If you need to move a downspout, it is generally better to replace the whole stretch of gutter instead of creating a new hole where water can find its way through. If replacing an entire section is not an option for you, it is possible to move the downspout and fix the hole without replacing the entire gutter.
What does a scupper look like?
Channel-type scuppers are three sided or are a simple rectangular hole cut in the wall. Some types can be round or a unique, decorative shape using custom sheet metal fabrication. These holes allow any water to drain straight down the sides of your building to prevent standing water and leakage.
Where do scuppers drain to?
Roof drains channel water through the deck of the roof into a piping system that carries water away, while a scupper allows water to drain through an opening in the side of the roof edge.
How does a scupper drain work?
In short, a scupper is a detail that provides drainage to a roof system by allowing the water runoff from the roof to exit the roof through a metal edge, parapet wall or through the deck into a downspout or leader not run through the interior of the building.
Are downspouts supposed to touch the ground?
Map the route of the pipes to identify the water’s path after it reaches the downspouts. Consider any slopes on the ground and the conditions of the soil. Your gutter downspouts should not touch the ground. Otherwise, the rainwater might get backed up in the gutter until it starts overflowing.
How far should downspouts extend from house?
As mentioned above, the water should be diverted at least 4 to 6 feet away from the house. If a home has basement walls, it should be at least 6 feet away. The furthest away from the foundation the better. Putting gravel or rocks at the end of the downspout to avoid erosion is a great idea.
What is a downpipe spreader?
Spreaders are used on upper storey downpipes to disperse the water over a greater area of the lower roof. Having a spreader in this position is quite ridiculous, it is a design fault of the plumbers and builders who built this guttering system.
How do you make a downpipe spreader?
Quote from the video:
Quote from Youtube video: And then down the wall a bit. So picture this is the flat piece down the wall. And then you've got to make up a spreader on the bottom of that to spread the water onto the onto the lower roof there.
How do slotted gutters work?
For a slotted gutter, the overflow is the bottom of the slots and this gives a gutter optioned with slots a smaller effective cross sectional area than a same profile un-slotted gutter. Gutters optioned with slots must be calculated to harvest a lesser maximum roof area than the equivalent un-slotted gutter.
Why do gutters have slots?
Despite this regulation, hundreds of thousands of houses have been fitted with high fronted gutters with no overflow provision, allowing water to flow back into the house. Slotted gutters have a smaller effective carrying capacity than a same sized unslotted gutter.
What is the correct fall on a gutter?
A good rule of thumb for a gutter slope is that you want at least a quarter inch of slope for every 10 feet of gutters.
How many downpipes Should a house have?
To calculate the minimum number of downpipes, divide the roof catchment area by the allowable maximum catchment per downpipe. To calculate the average catchment per downpipe, divide the roof catchment area by the number of downpipes.
