How do you read a gas meter reading?

Youtube quote:And the immediate right is near one or two record it is one number lower the pointer of the dial to the immediate right is near eight or nine. And that's it that's how you read your gas meter.

How do you read a gas regulator meter?





How Do You Read a Gas Meter?

  1. Read the dials with numbers only as you would do from left to right.
  2. Record the number each single hand points to. …
  3. Ensure you keep the current reading. …
  4. Keep in mind that the numbers slightly differ from those on your bill unless you read the meter simultaneously with your meter reader.


How does a gas meter work?

Rotary meters



With each turn, they move a specific quantity of gas through the meter. The operating principle is similar to that of a Roots blower. The rotational movement of the crank shaft serves as a primary flow element and may produce electrical pulses for a flow computer or may drive an odometer-like counter.

How do you read a diaphragm gas meter?

Youtube quote:If the dial points directly on top of a number always underline that number if it is followed directly by a 9 you should subtract 1 from that underlined number for example you would write down 0.

Why is my gas meter reading so high?





High gas bills may be due to a gas meter that is incorrectly recording the amount of gas you are using, but this is unusual. While there is no simple way you can test whether your meter is accurate, if you are concerned about your meter readings, contact your energy supplier.

What numbers do you read on a gas meter?

How do I read a dial gas meter?

  • Read the dials from left to right.
  • If the pointer is between two numbers, always take the lower number.
  • If the pointer falls between 9 and 0, write down 9.
  • Ignore red dials, ones marked ‘100 per rev’ and the largest dial.


What is a regulator on a gas meter?

A pressure regulator is a valve that regulates the pressure of a fluid or gas. Regulators are used for gases and liquids, and can be an integral device with an pressure setting, a restrictor and a sensor all in the one body, or a separate pressure sensor, controller and flow valve.

How do you adjust a gas regulator?



Youtube quote:You'll go back behind the piece of equipment. And unthread this silver cap that's in the very center of the regulator. Once you have that cap off you'll notice that there's a plastic adjustment.

How do you reset a natural gas regulator?

Youtube quote:First turn off all natural gas appliances unscrew the cap if it is a manual regulator. With your fingers pull the plunger. And then replace the cap.

What is a diaphragm in a gas meter?

Diaphragm Gas Meters are positive displacement type gas meters that utilizes flow channels designed for low pressure losses. The volume is displayed on a direct read (odometer) or clock (pointer) style indexes. Diaphragm Gas Meters design allows them to measure very small amounts of gas accurately.

What is the B button for on my gas meter?



This is your electricity reading. If your meter has an ‘A’ and ‘B’ button, press ‘A’ until you get to TOTAL ACT IMPORT. The number below this is your electricity reading. Your meter might have three buttons to the side of the display.

How do you read an analog gas meter?

Youtube quote:It goes left and then from the zero to the right and zero to the left and zero to the right set zero the dial is between 1 and 2 so you read a 1.

How do you read a natural gas residential meter?

How to Read a Natural Gas Meter

  1. Read the dials left to right.
  2. If the hand is between two numbers, always select the lower number.
  3. When the hand is between “9” and “0,” then “9” is considered the lower number.
  4. When the hand looks as though it is DIRECTLY on the number, look at the dial to the right.


How do you read a gas hand?



The cylinder is marked with numbers – usually F, ¾, ½, ¼. A red or yellow marker or float tells you how much fuel you have left; if the marker is at the bottom of the gauge or not visible, your tank is at or near empty. To make sure the gauge is working, carefully remove the outer case and gently press the float down.

How do you read a power meter?

Youtube quote:Write down the numbers from right to left. The result you obtain is the meter reading subtract. Your numbers from your previous. Read from your current read to determine your usage.

How do you read a gas meter with 4 dials?

Most CoServ Gas Customers have four dials on their meters and reading them is simple once you understand how. Read the dials left to right. When the pointer is between “9” and “0,” then “9” is considered the lower number. When the pointer on a dial is directly on the number, look at the dial to its right.

What is the difference between a gas meter and an electric meter?

In much the same way that a gas meter will tell you how much gas you have used, your electricity meter is the instrument that tells you how much electricity your household has consumed.

What is M3 on gas meter?



Digital metric gas meters measure gas usage in cubic meters (m3) and usually show ‘M’ or ‘M3’. 1. Write down all the numbers before the decimal point, left to right.

Is gas meter reading in m3 or kWh?

Check your meter says ‘M3’ after the reading. If it says ‘KWH’ it’s an electricity meter. If you’re not sure if it’s a smart meter, it might be a standard meter instead. Check how to read a standard gas meter.

How do you read m3 meters?

Youtube quote:Inside a meter box or maybe above ground to read the meter lift the lid to view the dire. The black numbers on a white background are kilolitres.