Can I cut a stud to install a medicine cabinet?

You will likely have to cut away part of a stud to make room, as most wall framing is set on 16-inch centers but many medicine cabinets are more than 18 inches wide. This requires not only cutting through the stud but disconnecting it from the wall behind it by slicing through the fasteners.

How do you fix the gap around a medicine cabinet?





You have a wood/melamine cabinet so yours is easy. drywall the wall and then cut out the drywall to the size of your cabinet using a utility knife carefully. Slip the cabinet in leaving it protruding about 1/2″ then caulk the perimeter around the cabinet and paint if you need to.

Is it okay to cut a stud?

Any stud in an exterior wall or bearing partition shall be permitted to be cut or notched to a depth not exceeding 25 percent of its width. Studs in nonbearing partitions shall be permitted to be notched to a depth not to exceed 40 percent of a single stud width.

Can you cut one stud on a load bearing wall?

As pointed out in the comments, you can’t simply cut a load bearing stud without any issues. Some sort of temporary support must be put in place to carry the load before you cut into existing structure and not removed until the new structure is in place.

How do I replace my bathroom medicine cabinet?

Quote from the video:
Quote from Youtube video: Basically we're going to remove four screws that secure this medicine cap you want to do is you want to take your blade. And you want to score around the corners or the sides.

Can you install a recessed medicine cabinet in a load bearing wall?





Installing a medicine cabinet in a load-bearing wall is doable, but if it’s not done properly it could lead to a sagging floor/ceiling. You may want to call a pro. However, if your cabinet is narrow enough to fit between two studs, then load bearing shouldn’t be an issue.

How do you fill gap between medicine cabinet and wall?

Position the backer rod in the gap between the cabinet and the wall. Add caulk to fill in the gap, but also to cover the backer rod and secure it in place. You can choose caulk in the color of your wall/tiles, or simply use transparent caulk so the color doesn’t clash with your bathroom design.

How do you fix a gap between a wall and cabinet?

But don’t despair, you can make these gaps disappear fast and easy with a caulking gun and a tube of caulk. You can use a colored caulk matching either the cabinet or wall color or paint white caulk to give your kitchen a more detailed, seamless appearance.

How do I fill the gap between shelves and walls?

Once the shelf is installed, use wood putty to fill the nail holes and any gaps between your mitres. Use caulking to fill any gaps between the wall and shelf.

How do you fix cut studs?



Quote from the video:
Quote from Youtube video: So first we cut our floor plate second we cut out seaming plate and third we cut our wall plates we fix these four Timbers in position fix through the edges with frame fixing screws.

Can I make an opening in a load-bearing wall?

Quote from the video:
Quote from Youtube video: And you don't know what you're doing okay all right what you have is a load-bearing wall seriously seriously. So does that mean we can't put a hole in the wall no no we can cut into it.

What happens if you cut a load-bearing wall?

Removing a load bearing wall may create structural problems in a home, including sagging ceilings, unleveled floors, drywall cracks, and sticking doors. Recognizing the warning signs of this is important.

Do I need a structural engineer to remove a load-bearing wall?



Usually, the removal of a load-bearing wall can be completed with a building notice, but the inspector may instruct you to hire a structural engineer who can specify an appropriate beam or lintel before they will grant approval.

How much of a load-bearing wall can you remove?

After all, in most homes you can remove as much as you wish of a load-bearing wall, but it has a lot to do with what’s inside the wall, and how you plan to redistribute the weight. Load-bearing walls are critical to the structure of your home.

How do you remove a stud without damaging drywall?

Cut the top and bottom of the stud with a Sawzall. If it is screwed from the other side and not nailed you may have to patch a couple holes but they may pull through clean. Just use a small pry bar and use as little force as necessary to pull the screws through the rock from the backside.

Does removal of a stud wall require building regulations?

Some non-loadbearing walls can be removed without notifying building control, but it is recommended that you check with a suitably competent professional, such as a structural engineer or architect, to identify the function and performance of the wall before determining whether it can be removed or requires an approval …

Can you reuse wall studs?



As long as the studs were end-nailed (not toenailed), they will be fine for re-use. If you are remotely concerned and time isn’t really an issue, cut 3/4″ off the ends and put in an extra plate. (The extra plate might help with raising the wall, too.)

Is a stud wall load-bearing?

A stud or partition wall, built with either plasterboard, or lath and plaster, is rarely constructed as a load-bearing structure. There are however exceptions to this – a stud wall may still help strengthen the structure of a building even though it may not technically be load-bearing (particularly in older homes).

How much weight can wall stud hold?

A screw in a stud can hold between 80 and 100 pounds. Be sure to distribute the weight across as many as you can.

How can you tell if a wall is load bearing without removing drywall?

Step 1: Determine Whether a Wall Is Load-Bearing or Not

  1. Check an unfinished basement or attic to see which way the joists run.
  2. If the wall runs parallel to the joists, it’s probably not load-bearing.
  3. If it’s perpendicular, it most likely is a load-bearing wall.