How do you strap a short water heater?
Wrap the heavy-gauge metal strapping 1-1/2 times around the tank. Start by placing the strapping at the back of the tank. Bring it to the front and then take it back to the wall. Secure this strapping to the wall studs or the wood block using several 1/4-inch x 3-inch or longer lag screws with oversized washers.
Can you use plumbers tape for water heater straps?
Note: Perforated iron strap (plumber’s tape) will not be an acceptable material for strapping or bracing water heaters over 40 gallons. Drill pilot holes on the centerline of the stud (both sides of the heater), Insert screws through punched holes in the strap. Use washers.
How tight should water heater straps be?
Minimum 22 Gauge metal strap material installed within the top 1/3 of the heater and the bottom 1/3 of the heater. The lower strap is installed minimum 4 inches above the control unit. Minimum 1/4-inch screws with minimum 1-1/2-inch penetration are allowed.
How do you double strap a hot water heater?
Quote from the video:
Quote from Youtube video: The lower strap must be high enough to be over the top of the water heater controls measure the tank first to position the straps. Now do the same for the other half of the straps.
How do you lift a water heater by yourself?
Quote from the video:
Quote from Youtube video: Start to tilt the water heater towards you as you are slowly stepping backwards. You will begin to feel the water heater slide off the stand. And set it down on the ground.
Do electric water heaters need to be strapped?
(1) All water heaters must be strapped, whether gas or electric. (2) Two straps are needed, one in the upper one-third and one in the lower one-third of the fixture. (3) Straps may consist of either plumber’s tape (at least 24 gauge) or half-inch-diameter metal conduit.
What are earthquake straps?
Earthquake straps are a must-have if you live anywhere prone to geological activity. They’ll hold heavy items of furniture in place during an earthquake to reduce the risk of damage and injury, and are especially recommended for bookcases, which can deal considerable damage if they topple.
Do water heaters need to be double strapped in Washington?
Water heaters shall be anchored or strapped to resist horizontal displacement due to earthquake motion. Strappings shall be at points within the upper one-third and lower one-third of its vertical dimensions.
Are water heater straps required in Oregon?
Installation: Portland plumbing regulations require that all homeowners and Portland plumbers follow specific water heater installation steps. For instance, “water heaters installed within 12 inches above the floor are required to be strapped between the top one third and top one-half of the tank”.
How do you put on a hot water heater brace?
Quote from the video:
Quote from Youtube video: And these are going to attach to the wall behind the water heater wrap. Around it and be secured with these pieces of hardware here. Um you'll want to compare this to what you'll find in some garages.
Why must a water heater be strapped?
The goal of water heater strapping is to make sure that the water line and gas don’t become disconnected as a result of the water heater shaking back and forth. In the event of an earthquake, a water heater has the potential to move in any direction.
Do you need a permit to replace a water heater in California?
Do You Need a Permit to Replace a Water Heater in California? Getting a water heater permit is essential, required by California law, and can be obtained from your local building and safety planning office.
Does New Mexico require earthquake straps?
It should be according to building codes.
Which States Require Water Heater Seismic Straps?
| U.S. State | Do You Need Water Heater Seismic Straps? |
|---|---|
| New Mexico | At least two 22-gauge metal straps. One strap on the top 1/3 of the unit and one on the bottom 1/3. Observes: New Mexico Plumbing Code |
What states is require hot water heater straps?
In addition to California and Alaska, areas of Nevada, Idaho, Wyoming, Montana, Oregon, Washington and Hawaii also fall under the Uniform Codes’ seismic zones 3 and 4, where water heaters are specifically required to be anchored.
Does AZ require water heaters to be strapped?
o Water heaters should be anchored to wall studs or masonry with metal straps and lag screws. Kits are available at hardware stores and home centers.
Does a tankless water heater need to be strapped?
All storage type (tanks) heaters require strapping – gas or electric. Tankless type heaters need not be strapped.
Are earthquake straps required in Utah?
Amendments to Chapter 5 of IPC.
As a minimum requirement, water heaters shall be anchored or strapped to resist horizontal displacement caused by earthquake motion. Strapping shall be at points within the upper one-third and lower one-third of the appliance’s vertical dimensions. “
