What is the hole for in the bottom of a hot water heater?

The dip tube is a long slender tube that fits down into the water heaters inlet, and usually has a small hole about 6 inches from the top. The dip tube directs the incoming cold liquid down to the bottom of the tank.

Should water heater drain valve be open or closed?





Its a good idea to run all of your hot water out of the tank before you drain it if you have one of these valves. Open this valve only far enough for water to drain from the tank. Don’t try to open it any more than necessary. Opening it to far will increase the chance of it coming off.

What is the valve on the side of the water heater?

On the side or top of your water heater tank is a valve connected to a metal or plastic discharge tube pointing downward. The valve is called a T&P valve, or TPR valve, for “temperature and pressure relief.” If all goes well, a TPR valve never gets used intentionally except during testing.

What does drain valve do on water heater?

Quote from the video:
Quote from Youtube video: And might leak.

Does every water heater have a dip tube?

Note that not all water heaters have a standard dip tube. If your water heater has its cold-water inlet located at the bottom of the tank, your water heater doesn’t have a dip tube.

Do gas water heaters have dip tubes?





Do All Water Heaters Have Dip Tubes? As a general rule, electric and gas water heaters have a dip tube. The dip tube connects to the cold water inlet, located at the top of the tank, and stops 6 to 8 inches from the bottom.

Should you open the pressure relief valve on a water heater?

Opening the valve on occasion will help ensure that it is working properly. Opening it will also help release any excess pressure that is built up inside the tank. This exercise could help you detect any leaks that your unit might have.

Should the pressure relief valve be up or down?

For most units, open the water pressure relief valve by simply lifting the valve up until the attached brass stem rises. When you do this, hot water will rush out of the pipe near the bottom of the water tank.

How often should you drain hot water heater?

every six months



Most homeowners should flush their water heaters every six months or so, but if you have extremely hard water, you may want to do it more often. Flushing your hot water heater could be necessary as often as every few months depending on the mineral content of your local water supply.

Will a water heater work without a dip tube?

In residential gas and electric water heaters, one important part you’ll hear about is a dip tube. It may not sound like the smartest piece of plumbing, but it’s a fact that your hot water won’t work well or last long without it.

Where is the dip tube located?

Quote from the video:
Quote from Youtube video: And money replacing incorrect parts let's get started the dip tube is on the inside of the tank. And is installed on the cold water supply.

Is a dip tube necessary?



Dip tubes, although simple, are very important to the operation of gas and electric water heaters. Without a dip tube you won’t get much hot water.

How much does it cost to replace a dip tube?

Dip Tube – $10 to $150



The dip tube carries cold water to the bottom of the tank for heating. If the dip tube is corroded, blocked, or leaking, water heating won’t occur as efficiently. On average, a new dip tube costs about $10, and it can run up to $150 to have it repaired professionally.

Is the dip tube and anode rod the same thing?

Remove the anode rod – you’ll see on most newer water heaters that the anode rod is a separate device from the dip tube – so you won’t have to disconnect the cold water supply piping. Instead take a look at the top of the water heater and you’ll see a hexagonal head marked “Anode”.

How much is a dip tube for a water heater?

Water Heater Dip Tube at Menards

Everyday Low Price $7.49
11% Mail-In Rebate Good Through 6/26/22 $0.82



Can a dip tube be replaced?

New water heaters have dip tubes that’ll last as long as the water heater. Or second, replace the defective dip tube with a cross-linked polyethylene one and flush the debris out of the water heater and the screens and filters. You may have to flush the system more than once.