What do you do when your oven says error?

Sometimes shutting off the circuit breaker that the range or wall oven is connected to for 30 seconds will clear the error, fault or function code. However, there are cases where the oven control does not reset and service may be required.

How do I reset the error code on my GE oven?





Turn off the breaker in your home’s electrical service panel and leave it off for a full 30 seconds. Then, turn the breaker back on. In addition to resetting your oven, this measure will force your oven to double-check its own diagnosis. If there’s no error in the unit, the error code will disappear after a reset.

Why is my oven beeping and F2?

In this case, the F2 error code indicates that the oven temperature is too high. Now, this does not necessarily mean that the temperature inside the oven really is too high. The oven control board (clock) is responsible for measuring the resistance of the sensor circuit.

What does f200 mean on GE oven?

December 6, 2021. Oven Repair. If your GE oven has an F2 (or F20) error code, the oven is detecting that the temperature inside the oven has exceeded a preset threshold. In plain English, it means the temperature has exceeded 615 degrees, or 915 degrees Fahrenheit during a self-cleaning cycle.

How do I reset my oven control board?

To reset it, just unplug the oven then wait about a minute then plug it back in. This should reset the board and clear any errors that are causing problems (if that is the case).

Where is the temperature sensor in my oven?





Quote from the video:
Quote from Youtube video: Six inches long so it has two screws holding it in and it's usually up in the top and the back somewhere this one's up in the top left-hand corner.

Is there a reset button on a GE oven?

Turn the circuit breaker to the OFF position or remove the fuse. Wait one minute, then turn the circuit breaker back to the ON position or install the fuse to reset power to the unit. This should reset the electronic controls on the range or wall oven.

How do you change a GE oven sensor?

Quote from the video:
Quote from Youtube video: Next remove the mounting screw to detach the old sensor. Gently pull the sensor forward and disconnect the wire by squeezing the tab. Be aware that if you are unable to easily reach the connector.

How do I clear F9 code on GE oven?

The F9 error usually means the door switch circuit system is faulty. This can be addressed by checking the door switch itself. If the door switch is dirty or caught in one position, use a damp cloth to wipe the switch clean and then wiggle the switch slightly to make sure the switch moves back and forth.

What does F3 mean on GE oven?



When the F3 code flashes on your GE oven, this indicates that there is a fault with the oven temperature sensor. There are a few parts that could be causing the fault. These include the wire harness, control board or the oven temperature sensor itself.

Why is my stove beeping F1?

Generally speaking “F1” implies an electronic oven control (EOC) failure, however it’s possible to have a bad oven temperature sensor probe (RTD sensor) causing the “F1”.

How do you fix F3 error on GE oven?

According to Hunker.com, to fix the F3 error code on a GE oven, you must purchase a new oven sensor. These sensors can be found at many local repair shops or online shops like Part Wizards. GE has their own specific model that also works in other brands of ovens.

Why is my oven beeping and F3?



When “F3” error code flashes, a small part known as the oven temperature sensor has encountered an error and fails to work anymore. According to Repair Clinic, the error means that a circuit has been exposed or broken.

What does F5 mean on GE oven?

Most common GE error codes

F0 This code usually means that there is a problem with the keypanel. Most of the time, it means that the keypanel needs to be replaced.
F4 This code usually means that the oven sensor needs to be replaced.
F5 This code usually means that the electronic control needs to be replaced.

What does F5 mean on an oven?

The F5 on most Whirlpool ranges will indicate that you have a problem with the oven door latch assembly or the oven door switch. Since you are seeing this error code when you are trying to set the self cleaning mode, this is likely the problem with your range. You could have a problem with the door switch.

Why does my oven keep beeping and F5?

A two-digit Whirlpool F5 code is a control board failure, according to Appliance Parts Pros, and the control board will need to be replaced.

How do you fix an F5 oven?



The “F5” error on General Electric ovens means that the safety circuit failed. This could occur because of a power failure or an error with the lock circuit. Unplug your oven for 30 seconds and plug it back in. If the error remains, replace the lock circuit, using the oven model number to find the proper part.

How do I fix F5 error on Whirlpool oven?

All F5-E Codes – Door Switch Defect – This occurs when the door switches do not match. If door is latched, disconnect power from unit and check wires and connections. If damage is found, replace appropriate part. If connections are not damaged, reconnect power and hold down any key until the F5 error clears.

What is F5 error code?

An F5 error code indicates that the fan on the outdoor or indoor unit has been running at a very low speed for a set period of time. This occurs when either the controller on the board or the fan malfunctions.

What is F5 on a whirlpool?

The “F5” error means that the temperature sensor has recorded an unusual reading while using hot water. This usually is a sensor error rather than a malfunction of your hot water heater.