Dig your hole to the required depth, 2½ – 3 feet if you can. The heavier the gate the deeper the hole needs to be. Place the post in the hole, get it level with the spirit level, and then backfill a small amount of earth around the sides.

How long should a gate post be?

Common standard lengths are 8, 10 and 12 feet. For outdoor construction, including fences and gate posts, rot-resistant lumber should be used. Cypress, cedar, redwood and pressure-treated fir or pine are popular choices. For a light to midweight gate, 4-by-4-inch stock is strong enough to support the gate.

Do gate posts need to be set in concrete?





Either way, concrete or solidly tamped dirt, your corners and gate posts, if braced properly, should be fine. Using a gate wheel on the longer posts also helps keep it all level, if you have level ground for it to set on. I would advise against using concrete if you can avoid it.

How do you put a gate post in the ground?

Quote from the video:
Quote from Youtube video: That's not deep enough let's get it to 30 inches typically you want to bury a post one-third of its overall.

How tall should a gate post be?

For an average fence post, about 6 to 8 feet tall, prepare to dig a post hole about 2 feet deep. To install a fence post, you’ll need a shovel or post digger, a 6-foot level, soil, and gravel or crushed stone. For gateposts, you’ll need concrete too.

How much concrete is needed for a gate post?

A 4″ diameter fence post needs a post hole that’s about 12″ in diameter. The depth below ground should be about 1/3 the height of the post above ground. For example, a 5′ high post will need about a foot and a half deep hole.



How Much Concrete For A 4×4 Fence Post?

Depth 50 Lb Bags
10″-14″ 2
16″-22″ 3
24″30″ 4
32″36″ 5





How do you install a driveway gate post?

Quote from the video:
Quote from Youtube video: Begin by mixing a batch of cement in the wheelbarrow. Empty a bag into the wheelbarrow. And have an assistant add water slowly while mixing the cement. Be careful to mix the cement thoroughly.

What depth should a fence post be in the ground?

2 ft

The 2 ft Rule



Lawsons experts recommend you should dig a hole which has a depth of 2 ft (24 in / 600mm) to ensure you have a stable timber or concrete fence post.

How much space should be between gate and post?



Allow 4.5 to 5 inches between the post and gate for hinges and pins.

What size Post do you use for a 6 foot fence?

Post lengths for fences start at 8 or 10 feet for a 6-foot-tall fence. They are commonly four-by-fours, which measure approximately 3 1/2 by 3 1/2 inches, or six-by-sixes, at around 5 1/2 by 5 1/2 inches.

How do you anchor a gate post to concrete?

Quote from the video:
Quote from Youtube video: Remove the base and then drill into the concrete using a hammer drill. And masonry drill bits. Move the post support back over the holes.

How do you concrete a gate post?



Quote from the video:
Quote from Youtube video: Get a piece of timber. And and give it a tap down with the timber to make sure that the fence post is absolutely surrounded by concrete. And then of course periodically.

Can you use Postcrete for gate posts?

If not, and you hit an unbreakable stone hopefully at least a foot or more deep (ideal depth is 2.5 or 3 foot) you can pour a wet concrete mix in the hole around your post, and leave for 24 hours to set. Alternatively, if you are in a hurry, you can use Postcrete, which sets in 15mins.

How do you install a steel gate post?

Quote from the video:
Quote from Youtube video: Put a little collar up top or plumb now on on the post this post over here we had to there's a bunch of number-two stone you can see I sitting here so we actually use a fence row stake.

How deep are metal gate posts?

The general rule of thumb when setting a post is that the depth of the post’s hole needs to be one-third to one-half of the actual above-ground height of the post. So, a six-foot-high finished post ideally needs to be buried three feet into the ground.

How much should be the gap between metal gate and post?



When determining hinge placement on the gate frame and post, be sure to account for the gap at the bottom of the gate. There is no standard bottom gap height, but you ideally want about 2-3” and to ensure the gate can freely swing all the way open and shut without contacting the ground.

Can steel posts be set in concrete?

Pour concrete with a strength of 20MPA and taper off at the top to enable water runoff. Make sure there is adequate concrete underneath the post. Check posts are at the correct level and plumb. You may need to brace the posts at the correct placement until the concrete is set.

How deep should a steel post be?

The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet).

How do I keep my post level while concrete dries?

You need to level it in two directions with a 4-foot level. After getting it straight in the first direction, hold one of the braces against the post and drive a single screw to connect the brace to the post. You can then level and brace the post in the other direction and begin filling the hole.

How do you brace a metal post for concreting?



Dig the hole so it’s at least twice the diameter of the metal post. Place 6 inches of gravel in the bottom of your hole for drainage. Place the metal post so it sits securely in the bottom of the hole atop the gravel and is centered. Shovel or pour 8 to 10 inches of gravel into the hole around the post.

How do you fit metal gate posts?

Quote from the video:
Quote from Youtube video: One of the J bolt should be facing up while the other one will be facing down. This will secure your gate in place install the J both in the direction that your gate will be swinging.

Do metal fence posts need concrete?

You can install a chain link fence without using concrete, but it is not recommended. Anchoring each fence post in concrete is the best way to ensure your fence will stand straight and tall for many years.