What do I do with the unused wire for ceiling fan installation?

  1. Use one switch on the wall to turn on/off the light.
  2. Use the other switch on the wall to turn on/off the fan.

What do you do with the red wire?

The exact purpose of a red wire for a light fixture can vary. Except in rare cases, it is a hot wire or a switched hot wire. Check the wire with a non-contact voltage tester with the power and switch turned on. If the tester indicates the wire is hot, turn the switch off and retest.

What do I do with the red wire when installing a light?





Red wires are usually used as secondary hot wires. Red wires are also hot and should be clearly marked to avoid the dangers of electrocution. Red wires are commonly used when installing ceiling fans, where the light switch maybe.

How do you disconnect a ceiling fan wire?

Quote from the video:
Quote from Youtube video: Slide the ball at the end of the downrod out of the mounting bracket. And then lower to the ground to remove a flush mount fan access the wires by removing the canopy.

Can you get electrocuted installing a ceiling fan?

It may seem like an obvious first step, but many people forget to first turn off the power to their home before performing any installation involving electricity. This is a fatal error that will almost certainly lead to electrocution.

Where does red wire go for ceiling fan?

Connect the green wire to your household ground wire (copper/bare wire). Connect your white wires together and secure with wire nut. Connect the red wire in the ceiling to the black wire in the light kit and the black wire in the ceiling to the black wire in the fan. Tuck the wires back into the box.

Does the red wire need to be connected?





Normally you’ll see a red wire in places you would expect a ceiling fan. But in places like a bathroom or a wall light, if you see a red wire, it’s a good bet that the red wire is the wire that’s connected to the light switch.

Can I put the red and black wires together?

These wires are typically used for switch wiring as well as the interconnection between smoke detectors hard-wired into the power system. You can link two red wires together, or you can link a red wire to a black wire. Since red wires conduct current, they are considered hot.

Why do I have a red white and black wire?

Black wires are hot wires that run to the electrical outlet from the switch. Red wires are hot wires common in a 240-volt outlet or when a wall switch controls the outlet. Blue and yellow wires are hot wires for ceiling fans and three- or four-way switches. White or gray electrical wires are neutral wires.

What are the red black white and green wires?

US AC power circuit wiring color codes



The protective ground is green or green with yellow stripe. The neutral is white, the hot (live or active) single phase wires are black , and red in the case of a second active. Three-phase lines are red, black, and blue.

What happens if you dont ground a ceiling fan?



So if you wire your fan without the ground wire, it will still work properly. However, the added safety of the ground wire will not be present. If you decide to wire your fan without the ground proceed to the next step.

What happens if you wire ceiling fan wrong?

Wiring the fixture incorrectly could lead to circuit breakers tripping, lights burning out quickly, or a ceiling fan turning in the wrong direction. Fortunately, this is something any homeowner can do with an inexpensive voltage tester.

Do ceiling fans catch fire?

A ceiling fan is still an electrical appliance; therefore, the potential is always there for a fire if wired incorrectly. However, the chances of a ceiling fan sparking fire are extremely rare. The fire hazard can be avoided by routine maintenance and inspection, almost ruling out the barest potential of fire.

Why is there an extra red wire?



In a three-conductor cable, the extra wire is red, and it’s almost always used as a hot wire. When you see a red wire in a 120-volt duplex outlet box, it’s usually because one of the outlets is operated by a wall switch, while the other is always on. The red wire is for the light switch.

Does red go to blue wire ceiling fan?

Typically when there is a red wire at the ceiling fan box it is connected to the blue light fixture wire of the ceiling fan. If there is a Black and Red wire then this usually means there are two separate wall switches, one for each function.

Do I need the red wire for ceiling fan?

Wiring a Fan With a Switch for Light and Pull Chain for Fan



In order for the light to be controlled by its own switch, the wiring between the switch and the fan unit needs a fourth wire, a red wire, to carry power to the light kit.

Can I connect blue and black wires together?

If you only have one switch, connect the black and blue wires. The black and blue wires need to be connected. You will be able to control your fan and lights with a single switch.

Can I connect the blue wire to the red wire?



Quote from the video:
Quote from Youtube video: And your installation guide states the neutral connection is optional. Simply place a wire cap on the white wire on your new.

What wires go together on a ceiling fan?

Look at the wires coming from your ceiling fan. The black wire from the ceiling fan is the hot wire that runs the motor and turns the fan blades. The white wire is neutral and completes the fan circuit. The blue wire is the hot wire for the ceiling fan light fixture.

How do you wire a ceiling fan with 3 wires?

Quote from the video:
Quote from Youtube video: First connect the ground wires. Together. Then the white. Now connect the light kits blue wire to the red wire in the ceiling. And the black wire from the fan to the black wire in the ceiling.