The Square D by Schneider Electric Homeline 30 Amp One-Pole Circuit Breaker is used for overload and short-circuit protection of your electrical system. This breaker is compatible with Homeline load centers and CSED devices. The ANSI-certified and UL-Listed unit is rated for 120/240 VAC and 10,000 AIR.

What would you use a single pole 30 amp breaker?

A single pole 30A breaker is used for 120V 30A circuits.

What requires a 30 amp breaker?





The 15-amp and 20-amp breakers often handle baseboard heaters, 30-amp serve water heaters and electric dryers, 40- and 50-amp are for electric ranges, and the 70-amp could serve a large air conditioner or a subpanel.

What is the difference between a single pole and a double-pole 30 amp breaker?

Single-pole breakers: Provide 120 volts, 15-20 amps and have one hot wire and one neutral wire. Double-pole breakers: Provide 240 volts, 20-60 amps and have two hot wires that share one neutral wire.

What is the difference between a 30 amp single pole breaker and a 30 amp double-pole breaker?

Distinctly, the difference between single-pole and double-pole breakers is how each is wired. Single-poles are wired with only one “hot” and one neutral wire. On the other hand, a double-pole breaker requires two “hot” wires that correspondingly share one neutral wire.

When would you use a 30A breaker?

Typically, a 30-amp breaker is designed for heavy-duty appliances like HVACs and water heating systems. Besides, it can only accommodate 30-amp receptacles if it’s a single-outlet circuit breaker. If it’s a multi-outlet device, we can install a 20-amp circuit to protect the #10 conductor.

When would you use a single pole circuit breaker?





Quote from the video:
Quote from Youtube video: Service and amperage single-pole breakers are most appropriate for non heating or low amperage household use double pull breakers are warranted for power sources requiring. Higher voltage.

How many outlets can I run on a 30 amp breaker?

A good rule of thumb is to put a maximum of 16 outlets on a 30 amp circuit. The 30 amp outlet chart below tells you when you should put 1, 2, 3, 4, 6, 8, 12, 16, and 24 outlets on a 30A circuit.

How much can you run on 30 amps?

3600 watts

A 30-amp RV system uses 120 volts. Multiply 120 volts by 30 amps and we get a maximum allotment of 3600 watts.

Can you use a 30 amp breaker for a electric stove?



Because most stoves are 240 volts, it is best to use a double-pole circuit breaker on a dedicated circuit inside your electrical panel. Electric stoves often require a 30 to 60 amp circuit breaker.

Do I need a single or double pole breaker?

The main difference between a single vs double pole breaker is their power capacity. Single-pole breakers are typically used for low-power appliances, as they can provide 15 to 20 Ampereges and 120 Volts. Double-pole breakers protect heavy machines, as they can provide 20 to 60 Ampereges and 240Volts.

What does single pole breaker mean?

Single-pole breakers are the breakers that control virtually all the standard lighting in your home, and all standard 110-volt outlets with standard two-slot outlet receptacles. Whenever a circuit trips and the lights and appliances along that circuit fall dark and quiet, it is a single-pole breaker you should inspect.

What does Single Pole mean in electrical terms?



A single pole switch has one input and one output, it has two states; “on” or “off”. They can be wired either normally open or normally closed and can be either latching or momentary.

What appliances require 30 amps?

Now that you know this, here are some examples of what you can run on a 30 amp 120 volt power box:

Appliance Watts Needed
Clothes washer 400–500 Watts
Hair dryer 1250–1875 Watts
Clothes iron 900–1800 Watts
Microwave oven 800–1100 Watts

What does 30 amp circuit mean?

A 30 amp plug has three prongs – a 120 volt hot wire, a neutral wire and a ground wire – and is generally used on RVs with lower load requirements. A 50 amp plug has four prongs – two 120 volt hot wires, a neutral wire and a ground wire – that supply two separate 50 amp, 120 volt feeds.

Can you plug a 15 amp appliance into a 30 amp outlet?

Receptacles, switches, etc. – Everything needs to be rated to match. You can’t use a 15A or 20A receptacle on a 30A breaker because if you had an overloaded device (not planned – malfunctioning) that pulled 30A, it would melt the receptacle but the breaker wouldn’t trip to stop it. Devices – lights, appliances, etc.

How many amps does a refrigerator use?



Refrigerator amps are the amount of electrical current it’s compressor uses to cool it’s compartment. Amperage for most household refrigerators, is anywhere from 3 to 5 if the voltage is 120. A 15 to 20 amp dedicated circuit is required because the in-rush amperage is much higher.

What can you plug into a 30 amp outlet?

Quote from the video:
Quote from Youtube video: Anything. If however you are referring.

How many lights can you put on one breaker?

To figure out “How Many Lights Can Be Installed on One Circuit Breaker,” you have to know the following. 50 watt light equals less than 1/2 amp current flow at 120 volts. You can put up to 30 lights (based on 50 watt light) on a 15 amp breaker. You can put up to 40 lights (based on 50 watt light) on a 20 amp breaker.

Can I put outlets and lights on the same circuit?

Generally a properly wired home should have dedicated lighting circuits that are apart from receptacles. Overloaded neutrals are fire hazards.

How many amps does a microwave use?



The microwave ovens consume power at a rate of 650– 1200 watt, which equates to a current of around 10 Amps.