Can you install a 12-inch rough in toilet with a 10-inch?
A toilet with a 12-inch rough-in will definitely not fit into a space with a 10-inch rough-in, but a toilet with a 10-inch rough-in actually has extra space in a 12-inch rough-in space.
How do you install a toilet drain in concrete?
Quote from the video:
Quote from Youtube video: And driving them with a nut driver. Bit. Continue around the flange drilling holes and securing into place with the concrete anchors. Once the flange is secured. The floor can be tiled and the toilet.
What does 10-inch rough in mean for toilet?
Keep in mind you need some space on the sides as well. Toilet Rough In Dimensions: A toilet’s rough-in measurement is the space between the wall behind the toilet and the center of the waste pipe. Standard toilet rough in dimensions are 12 inches but can be anywhere from 10 to 14 inches in some cases.
How do you move a toilet rough in?
Instructions
- Remove the Toilet. Remove the toilet from its current location. …
- Gain Access. …
- Remove the Toilet Flange. …
- Cut the Toilet Bend. …
- Position the New Drain Location. …
- Run the New Drain. …
- Install the Drain Stub-Out. …
- Run the Water Supply Lines.
How do I make sure my new toilet will fit?
Quote from the video:
Quote from Youtube video: So the way to do that is is to measure from the wall. To the center of the cap or the bolt that bolts your toilet to the floor.
What is the standard rough-in for a toilet?
12 inches
Standard Toilet Rough-In Sizes
The standard toilet rough-in is 12 inches, but don’t assume you have a 12” rough-in without measuring! Some older homes come with 10” or 14” rough-in sizes. You may also find 10” rough-in sizes in powder rooms, half baths, or other small bathrooms to save space.
How do you install a toilet in a basement with a rough in pipe?
Quote from the video:
Quote from Youtube video: And just clean the inside of the pipe up make sure this size clean on the flange. And fit it in it'll sit flush with the floor when it's pushed down finally but it's pretty tight.
How do you rough plumb a toilet?
Quote from the video:
Quote from Youtube video: So if you're just replacing your toilet. And notice your flange is only 10 inches from the wall. There's no need to move your flange. Just get a water closet with a 10-inch roughen additionally.
How far should a toilet be from the wall?
Most codes require at least 15 inches (measured from the center of the toilet) from any side wall or obstruction and not closer than 30 inches center to center to any other sanitary fixture. (The NKBA actually recommends 32 inches.) There should be at least 24 inches of clear space in front of a toilet or bidet.
How do you measure toilet rough opening?
The rough-in measurement of a toilet refers to the span between the wall behind the toilet and the center of the waste pipe. To measure the rough-in for your toilet, measure from the wall behind the toilet to the middle of the bolt caps (the caps holding your toilet to the floor).
How far off the wall is a toilet flange?
12 inches
The Distance To Set The Toilet Flange From The Back Wall. You’ll want to set the center of the water closet flange 12 inches from the finished back wall.
Should toilet flange be flush with floor?
Quote from the video:
Quote from Youtube video: Thing you want to do is remember that all toilet flanges should always be installed on top of the finished floor.
How far should toilet flange be above finished floor?
1/4 inch
With the toilet removed, you can see the toilet flange and measure its height above the floor. The optimum flange height to aim for is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal.
How far can you offset a toilet?
The typical offset is 12-inches for most residential toilets. As a result, the toilet had 4-inches behind the tank.
How far can you move a toilet drain?
You can move a toilet as far as you wish to. However, you may need to drill a new hole in the floor and install a new wastewater pipe. This will result in a lot of investment at your end. However, you can also move the toilet to a certain extent without having to change the waste line and stack.
Can you turn a toilet 45 degrees?
Quote from the video:
Quote from Youtube video: This is the case. And you have a standard toilet. There's a good chance you'd be able to do something like this even though it would be uncomfortable.
