The flashing that covers the “joint” (space) between the wall above and the roof below is called “counter-flashing”. Usually there is a piece of metal flashing that is layered into the roofing plies and turned vertically up the wall.
What is the area between the roof and the exterior wall known as?
Eave: Where the roof hangs over the edge of the exterior wall. Fascia Board: Generally a 1” x 6” Pine board which covers the ends of the rafters. Oftentimes, the fascia board may have a sub-fascia which is typically a 2×4 or 2×6 pine board.
What is it called where the wall meets the roof?
A headwall is a level junction where a roof meets a wall. This illustration shows proper flashing at a headwall condition. Headwall flashing should extend up behind the exterior wall covering and down over the roof-covering material, as you see here.
Why is there a gap between the wall and roof?
Some gaps, such as an eave gap between the top of the wall and the underside of the roof are there for attic ventilation.
Should there be a gap between wall and soffit?
Remember to leave a general gap between two lengths of soffits of at least 5mm to allow ‘thermal movement’ to take place without warping the soffits when they press together.
What is the seam of a roof called?
The line where two adjacent sloping sides of a roof meet is called the hip. Louvers: Slatted devices installed in a gable or soffit (the underside of eaves) to ventilate the space below a roof deck and equalize air temperature and moisture.
What is the trim on the outside of a house called?
fascia. Trim is the material used to encase windows and doors, among other features, on a home’s exterior. Fascia is a horizontal or angled board that encloses the edge or face of the projecting eaves.
Should there be a gap between roof and fascia?
This gap is caused when roof decking is stopped too short and is not flush with the fascia. The gap is meant to help with airflow throughout the attic. However, this gap is the perfect place for pests and unwanted wildlife to enter your home.
How do I fix the gap between my roof and fascia?
Start at the end of a fascia board and caulk the corner edge where two boards meet. Smooth the caulk bead with your finger and begin caulking the joint between the fascia board and the soffit (also known as the eave). Slowly move down the joint to apply a steady bead of caulk into the gap, instructs Ron Hazelton.
How do you fill an outside wall gap?
Quote from the video:
Quote from Youtube video: So what you can do is get some mortar mix from your home. Center. Which is pretty easy to to mix up you just follow the directions. It's just powder you add some water to it.
What’s a roof purlin?
In steel construction, the term purlin typically refers to roof framing members that span parallel to the building eave, and support the roof decking or sheeting. The purlins are in turn supported by rafters or walls.
What is soffit and fascia?
An exterior soffit is located on the span beneath the rafter tails, while the fascia is the exposed horizontal band you see at the end of the rafters. These architectural elements found along the eave area do more than just add visual interest and give a finished look to your home.
What is a seam Batten?
Description: Batten seam roofing consists of copper pans running parallel to the roof slope, separated by wood battens. The battens are covered with copper caps that are loose locked into adjacent pans. The width of these preformed or field formed pans may vary.
What is a standing seam metal roof?
Standing Seam Metal Roof Systems
Standing seam metal roofing is a concealed fastener roofing system which features vertical or trapezoidal legs with a flat space in between. This metal roofing system from MBCI is one of the most durable and weather-tight roof systems available in the industry.
How are metal roofs attached to the home?
The majority of metal roofs currently in use today hold themselves in place by means of mechanical fasteners – usually corrosion-resistant bolts or screws that anchor the roof in the underlying decking material. Fasteners generally fall into one of two categories: exposed or concealed.
Can you walk on a standing seam metal roof?
Standing Seam Metal Roofs – can be easily walked on without damage, but they are steep and slippery. Safety equipment use is a necessity. Corrugated Steel Roofs – are also easily walked on without damage as their installation is done directly to the roof decking.
