it helps the table to sit flat, or at least not concave, with the weight of the router. it ensures that the workpiece contacts the table right next to the bit, even if it is not quite touching out at the edges.
How do you use a router plate insert?
Quote from the video:
Quote from Youtube video: So roughly get it positioned where it needs to go and then I can draw around the router base to work out where I'm going to need to cut. I drill a pilot hole in the center.
Why do you need a router insert plate?
A router plate is a convenience. Not a necessity. It provides a means to remove the router from the table for such things as bit changes. If one has a router that can be left in the table (i.e. a dedicated router) and has a router lift that allows raising the router to change bits, then the plate is not necessary.
What is a throat plate on a router table?
The throat plates are components of the table that consist of five yellow plastic rings. They serve as a guide for the router bit and provide a stable surface around the bit.
How do you level a router plate?
Quote from the video:
Quote from Youtube video: Between a 30 second and a 16th of an inch. Below table level. And instead of trying to shim the plate up the level we're going to use four of these. These are one-quarter inch wide rubber o-rings.
How do you use a router ring?
Quote from the video:
Quote from Youtube video: And they just pop right in here on. The bottom and then this little band gets screwed into the other. Side.
What are router bushings used for?
A little mysterious, but very useful. Guide bushings are simple devices that when used properly, extend the capabilities of your router. The bushing fits into the hole in the routers baseplate and is designed to follow a template, which guides the router bit, transferring the templates shape to another piece of wood.
How do you use a centering cone on a router?
Quote from the video:
Quote from Youtube video: From there install the base making sure that the cone is well below the base of the router to start next loosen the screws on the base plate. And then lower the base plate slowly. Into the cone.
What is the bearing for on a router bit?
Bearing Guides are used on many router bits. Rabbet bits, chamfer bits, ogee bits, flush trim bits all use bearing guides to route to a precise pattern. Even raised panel bits and stile and rail bits use bearing guides. These bearings can be used to replace worn out bearings or to modify the cut depth of router bits.
How do you use a router inlay bushing?
Quote from the video:
Quote from Youtube video: Along the template okay kind of cutting. Out exactly where you need it correct. And then you just fill in everywhere that it doesn't reach correct so we'll actually just trace the outside.
How do I make my router recess?
Quote from the video:
Quote from Youtube video: To make the router setup right I'm going to take the depth of the jig at 3/4 plus the first 1/8 setting. My little square here at 7 eighths of an inch. Perfect. And then I'll continue 1/8.
How does a router inlay kit work?
Quote from the video:
Quote from Youtube video: But it also has a bearing or a bushing that goes around that piece and the way it works is the first cut that you make into your work surface has these two combined.
How do you put a router inside a frame?
Quote from the video:
Quote from Youtube video: The first router bit I used is a rabbeting bit which will add a groove to the inside edge of the back. This groove will hold the picture and glass in the frame.
How do I make crown molding?
Quote from the video:
Quote from Youtube video: Using two or even three of the profile bits to make a complex crown molding we simply add the cutting width of each of those three bits to the 3/4 of an inch we need for our crown molding edge.
How do you cove molding on a router?
It’s best to route the cove on a larger board and then rip it down to size on a table saw.
- Clamp the poplar board to the edge of a worktable with a clamp at each end. …
- Insert a 3/4-inch cove bit into a hand router. …
- Loosen the height-adjusting knob on the router. …
- Hold the router with hands on both knobs.
