That’s a cover for your drain clean out. If water is leaking out of there then either the threaded cap below, if there is one, is loose or there is a blockage starting to form and the drain water is starting to backup because it can’t go down the drain fast enough.
What is the metal plate on a tub for?
Your bathtub has several working parts. One of the most important is the overflow cover plate. As the name implies, the cover is designed to prevent water in the bathtub from overflowing. When water overflows from the tub, it can cause significant damage to the floor, other appliances, and the bathtub.
What is the pipe next to my tub?
What is this thing for? Part of the drainage system for the tub. Your tub has no overflow drain, so the standpipe will take over just in case.
How does a bathtub overflow plate work?
The water that enters the overflow hole, goes down a pipe which is connected to the tub floor drain. With a well-functioning overflow drain, excess water will flow out the overflow hole, through the pipe and into the drain so as not to cause any damage to your bathroom or anything under or around the tub.
What is a tub overflow drain?
What is an overflow drain? The point of an overflow drain is to collect the excess water for your bathtub or faucet. The drain collects the water, preventing it from overflowing if you accidentally leave it on.
What is the silver thing in the bathtub?
That is the tub drain overflow plate, though it’s actually above the drain, not the faucet. (The opening in this plate leads to a tube that prevents the tub from overflowing by allowing water to run out even if the drain in the bottom of the tub is stopped.)
How do you replace a faceplate in a bathtub?
How to Replace a Bathtub Faceplate
- Unscrew the two screws holding the trip-lever faceplate to the overflow. …
- Once you have the screws removed, lift the faceplate and assembly from the overflow. …
- Tip the faceplate forward until you can see the backside clearly. …
- Remove the cotter pin from the linkage arm.
How do you remove an overflow plate from a bathtub?
To remove it, place your thumbs at the bottom of the cover plate and press gently upward until the plate snaps free of the underlying mount and pops off in your hand. Depending upon whether you’re troubleshooting, cleaning or upgrading, you can snap the same cover plate or a new one over the same mount.
How do you stop a bathtub overflow drain?
The quickest and easiest way to stop a bathtub overflow is to use a reusable overflow cover. Simply place the cover over the overflow on your bathtub to seal it up and stop water escaping through the overflow and down the drain. Giving you a deeper soak.
How do you clean a bathtub overflow drain?
Start by removing the screws on the drain’s overflow escutcheon plate. Next, pull the drain assembly out of the overflow pipe. Clean any hair and debris from the drain bail. A two-foot long flexible rod with tiny bristles on the end, known as a drain stick, is used to remove any additional gunk from the drain.
Where is the trap on a bathtub drain?
Quote from Youtube video: Here comes down and comes right back into the drain. And then trying to flush like here to see if it helps but inside the cavity here that's in between the floor joists is the pea trap or the trap.
How do you remove a tub drain cap?
Quote from the video:
Quote from Youtube video: If the stopper does not come out of the drain. Look for a set screw underneath the top of the stopper loosen the set screw and remove the top of the stopper.
How do you remove a drain cover?
Insert the tip of the screwdriver through an opening in the cover and lift up. For a snap in cover, spray lubricant along the edges of it as well. Let it settle down into the threads. Insert the needle-nose pliers into the openings of the drain cover, firmly grip the pliers, twist it towards the left, and pull it out.
How do you replace a bathtub drain flange?
Quote from the video:
Quote from Youtube video: Here let me put it back in tighten it up a little bit you could always take a screwdriver lift it up and take a screwdriver and take that screw out to remove the drain plug.
How do you remove a shower drain grate?
Quote from the video:
Quote from Youtube video: One get yourself some wd-40 spray it around the rim of the drain. Let it sit for about 15 minutes or so and then get yourself some pliers that fit into these holes in the drain.
Should there be standing water in shower drain?
Yes it’s normal and what you want. It’s called a P-trap and the water sitting in there seals out the sewer gasses.
Do shower drains have a trap?
The shower drainage features a piping that has a trap as part of its key components. The trap in the shower drain works like the one beneath the kitchen sink. While the sink trap is P-shaped, you may find some S-shaped shower traps.
