When applying epoxy:

  • Wear long sleeved tops and long trousers.
  • Wear shoes and socks since epoxy will drip onto feet.
  • Wear disposable vinyl gloves.
  • Tape over the joint between the gloves and the sleeve if necessary.
  • Take care not to rub the wrist with the dirty fingers of the other hand when removing gloves.

How do you use epoxy resin for beginners?

Quote from the video:
Quote from Youtube video: If. You have a steady hand you can just pour it straight into the mold. But I like to err on the side of caution. And there you have it.

Is epoxy resin easy to work with?

Relatively speaking, epoxy is the easiest to work with. It’s the most forgiving of beginner resin mistakes, plus it’s the easiest to mix and measure.

Is resin difficult to work with?

Mixing resin can be a little intimidating but once you get the process down it’s the same steps over and over: mix resin, pour, pop bubbles, layer resin, let cureā€¦ Regardless of the number of layers you put in your resin piece the basics are the same which makes it pretty easy to learn.

What are 3 important tips when pouring resin?

Do you have any resin pouring tips?

  • Apply the resin a little bit at a time. Depending on the resin, it can pour quickly. …
  • Leave a bit of resin in the bottom of your pour cup. You can then check the resin in the cup to check to see if your resin is cured. …
  • A heat gun is great for removing bubbles from your resin.


How long do you let resin sit before pouring?

Layering in molds – allow each layer to set up for at least 3 hours before pouring next layer. Doming – you can apply your resin right after the 5 minute rest period, or let the resin thicken for up to 25-30 minutes.

How do you spread resin evenly?

Pour the resin evenly over the surface and spread the resin to each edge and corner with your hands (while wearing gloves), a plastic spreader, a brush, or something disposable like a popsicle stick. Even if the resin you are using is self-leveling, it’s a good idea to spread it out manually.

How do I stop my epoxy from dripping over my edges?

Quote from the video:
Quote from Youtube video: You take your blue tape painters tape and on the bottom of your piece you tape it off makes it simple then when the resin runs over the sides. The next day you can just pull off the tape.

Can you pour epoxy on uneven surface?

If you have an uneven surface to begin with, epoxy resin can be used to make it more level to great effect. Inherently, all of our resins have self-leveling properties that help them flow to coat a surface evenly. You can also use them to seal surfaces that are porous or have little holes, such as wood or stone.

Can you pour epoxy over cured epoxy?

Can I put another coat of epoxy over cured epoxy? Yes. Since the epoxy has cured a chemical bond is not possible so what is called a mechanical bond is needed. This simply means that the cured epoxy has to be lightly sanded before the next coat is applied: the first coat should have a matt, almost white, surface.

How long should you wait between coats of epoxy?

When using epoxy, it can be a helpful process to add a second layer, but you want to make sure to follow the correct procedures. With most coating epoxies, if you are trying to build up to your desired thickness, it is recommended to pour your second coat once the first coat is tacky to the touch (usually 4-6 hours).

Why am I getting dimples in my epoxy?

Dimples can occur for 3 reasons: temperature fluctuation, micro dust particles and overtorching. To avoid getting dimples in your cured resin, make sure that the temperature in your resin room stays stable, that you use a dustcover and that you only lightly torch your resin!

Do you have to sand between coats of epoxy resin?

Sanding epoxy resin between coats will not only get out the imperfection, but will also serve to provide some tooth between the first and second layers.

Why is my epoxy bumpy?

This problem can be caused by anything floating/falling into your resin while it cures, resulting in imperfections in the surface. If you are experiencing imperfections that look more like domed bumps in the resin, skip down to #4.

How thick can you pour epoxy?

It was designed for thin applications and naturally self-levels to about 1/8″. As long as you pour in 1/8″ layers, you can go as thick as you like. The reason we recommend this thickness is two-fold: first, it allows the bubbles to escape properly, and second, it avoids any excessive overheating of the resin.