The easiest option would be to simply use 12 ft sheets of 5/8 fire rated sheetrock and rent a lift to do the ceiling with. A lift is very easy to use and almost makes it a one person job. Personnally, I’d also use 5/8 on the walls as well.
What thickness drywall should I use in my garage?
5/8-in.-
Drywall is the easiest and most economical covering for your garage ceiling. Use 5/8-in. -thick drywall if your trusses or rafters are spaced 24 in. apart.
Can you hang drywall on 24 centers?
drywall has always been approved for use on 24-in.
Can you use 3/8 drywall wall?
3/8-Inch Drywall: Just slightly thicker than 1/4-inch drywall, 3/8-inch drywall is also a good choice for curved walls. This thickness is most often used to repair existing drywall that needs patching.
When should you use 5/8 drywall?
5/8-Inch-Thick Drywall
These panels are commonly used for ceilings or for walls that require a prescribed fire-resistant rating.
What size screws 1/2-inch drywall?
When working with 1/2-inch drywall panels, use 1-1/4 or 1-3/8-inch nails or screws. When working with 5/8-inch drywall panels, use 1-3/8-inch or 1-5/8-inch screws. To properly secure drywall, the right number of drywall fasteners should be used.
What is code for distance between studs?
Utility-grade studs shall not be spaced more than 16 inches on center or support more than a roof and ceiling, or exceed 8 feet in height for exterior walls and load-bearing walls or 10 feet for interior nonload-bearing walls.
How many screws go into a sheet of drywall?
How Many Screws Per Sheet of Drywall. Use about 32 drywall screws per sheet of 4-foot by 8-foot drywall installed horizontally on a wall. This total is comprised of four screws on the five middle studs and six screws on each of the two sides.
Which direction should you hang drywall?
On commercial jobs, fire codes often require seams to fall on the entire length of the framing, so the drywall must be hung vertically. However, on residential jobs, the drywall on the walls is typically hung horizontally. For walls 9 feet high or shorter, hanging the drywall horizontally has a number of benefits.
Is half inch or 5/8 drywall better?
Quote from the video:
Quote from Youtube video: Half inch sheetrock is what you see in most homes on the walls. And probably the last five to ten years we've started using 5/8 sheetrock on the ceilings. It gives a much stiffer.
Should I use #6 or #8 drywall screws?
In most cases, you will be using either #6 or #8 drywall screws. Keep in mind that as gauge numbers increase, the screw becomes larger in diameter. So, a #6 drywall screw would be thinner than a #8 drywall screw. While this may seem evident, many materials related to home construction work in the opposite direction.
How far should drywall screws go into studs?
As you finish, the head of the screw should be just barely recessed below the surface, no more than 1/8 inch.
How often should drywall be screwed?
Drywall screws should typically be placed about 12 to 16 inches apart. However, the spacing changes when hanging drywall edges and ceilings.
How far should drywall be off the ceiling?
In fact, when you’re hanging the ceiling, keep in mind that 1/2 in. along the perimeter will be covered by drywall on the walls. And the same is true of inside wall corners. So you can safely cut these pieces 1/4 in.
Should drywall be installed vertically or horizontally?
Final Thoughts. In short, drywall should be hung horizontally on residential buildings and vertically on commercial buildings. In the case of either, support beams should always run perpendicular to the wall studs at a distance of 24 inches (61 cm) apart.
Should drywall joints be staggered?
Drywall butt joints should always be staggered. This makes it easier for taping and finishing and increases the overall strength of the entire wall.
Should drywall be butted tight?
Vertical joints in drywall are also called “butt joints.” Always leave a 1/2-inch gap at the floor. This allows for floor and wall expansion without cracking the drywall. It also helps prevents moisture wicking if the floor floods.
Should drywall touch the floor?
Drywall should NOT touch the floor. Allow for floor and wall expansion without cracking the drywall by keeping a 1/2-inch (1.27-cm) space between them. This space also aids in preventing moisture from seeping if the floor floods.
