How do I hook up the water line to my ice maker under my sink?
How to Hook Up a Water Line to a Refrigerator From the Sink
- Find your water supply lines beneath your sink. …
- Attach a 5/16-inch drill bit to your drill. …
- Thread the water line, included in the ice maker installation kit, from the area behind the refrigerator to beneath the sink.
What size pipe is ice maker line?
1/4-inch
The tubing should have a diameter of 1/4-inch and can be copper line, braided steel line or plastic tubing. Many professionals prefer copper line, but plastic tubing is commonly sold as part of ice maker installation kits.
How do you tie a water line to an ice maker?
Quote from the video:
Quote from Youtube video: So I did a couple of feel of bits and of course the first one right into this joist the joist right behind this. So I did another one and that at least establishes which Bay we can now drill.
Is PEX good for ice maker?
COMPLETE ICE MAKER WATER LINE KIT: Crosslinked High Density Polyethylene, PEX, hose is extremely durable. It won’t corrode and can’t be damaged from expansion or contraction. Easily withstands temperature and pressure stresses that occur in water systems.
Where is the water line on a refrigerator?
The water line connected to the refrigerator should have its own shut-off valve connected to the cold water supply line in the home. The shut-off valve is usually located under the kitchen sink, in the basement, in a crawl space or in the cabinet next to the refrigerator.
Can a fridge make ice without a water line?
Although it’s convenient to get water and ice directly from the refrigerator, purchasing a refrigerator without a water line or reservoir doesn’t mean you can’t have homemade ice or chilled and filtered water. Ice cube trays require minimum effort to fill with water, freeze and extract.
Is ice maker line same as water line?
The ice maker supply line is a small plastic, copper, or stainless steel water line that feeds directly into the ice maker. Water pipes are very susceptible to damage it is important that while installing or once it has been installed it is in a position where it is not being bent or shaped in an awkward position.
What size is ice maker connector?
1/4-Inch
A 1/4-Inch female compression thread by 1/4-Inch female compression thread connector with an efficient flow rate..
What size is a refrigerator water line connector?
Most flexible copper refrigerator water lines have an outside diameter of 1/4 inch. Most flexible plastic water lines for refrigerators come with outside diameters of either 1/4 inch or 5/16 inch, reveals Darrin’s Plumbing Tips.
Can I use plastic tubing for ice maker?
Answer: You’re right to be concerned, because plastic tubing to an ice maker is susceptible to cracking and splitting. The constant flow of hot air from the compressor fan in the essentially unventilated space behind the fridge blows over and around the tubing — and eventually makes it quite brittle.
What is PEX water line?
PEX, short for cross-linked polyethylene, is a flexible plastic used for plumbing. The tubing has become quite popular over the years, replacing traditional copper and galvanized steel water supply lines.
What type of tubing is used for a refrigerator water line?
Braided stainless steel tubing is the option I recommend. It might cost you a few dollars more, but it will last longer and, like I said, is very easy to work with. A Valuable Tip: Make sure you leave extra tubing behind your fridge so you can pull it out to clean behind it. Give yourself an extra 5 or 6′ of line.
How do you install a water line for a refrigerator?
Instructions
- Turn off the Water. Locate the fixture shutoff valve on the cold water supply line under the kitchen sink. …
- Disconnect the Faucet Water Line. …
- Connect the Tee Adapter. …
- Connect the Faucet and Refrigerator Supply Tubes. …
- Connect the Supply Tube to the Refrigerator. …
- Turn on the Water.
Is copper or plastic better for fridge water line?
Sometimes referred to as poly, plastic tubing is flexible and easier to install than rigid copper tubing. Plastic also allows the refrigerator more freedom to move with less fear of damaging the tubing. However, plastic is not as durable as copper, and the tubing can still get damaged and spring a leak.
How much does it cost to install a water line for a refrigerator?
A typical water line costs between $65 and $170 to run. The cost to install a basic refrigerator on a first floor kitchen with a water line is about $250. If you need an electrical outlet installed by an electrician, you’ll need to pay an average of $220-$750 per outlet.
How much does it cost to tap into a water line?
Average Cost to Hook Up to City Water & Sewer
Although the price of $500 to $20,000 to connect to the city usually includes water and sewer hookup, it often does not include installation for either line. Water main installation costs $1,600 on average. In many cases, your plumber can do both projects for you.
Does a new refrigerator come with a water line?
Most new refrigerators do not come with a water line. You have to purchase a hose for installation. Metal hoses for a refrigerator have a standard 1/4th inch connector and come in varying lengths. The length you need depends on the distance between your fridge hook up and the sink valve you connect to.
What can I use instead of a saddle valve?
A similarly DIY-friendly but more reliable alternative to a saddle valve is a push-fit tee connector designed for ice makers and water dispensers. You install these by cutting out a short section of pipe and installing the tee right into the water line, then adding the small supply line leading to the appliance.
How do you change a shut off valve on an ice maker?
Quote from the video:
Quote from Youtube video: So you tighten up the knob. And after you tighten the knob. Just just just a little bit and then you swing it around the pipe.
Are saddle valves against code?
Saddle valves are against plumbing code now because they are prone to leaks. Leaks create corrosion to the rest of the plumbing system.
How do you install a saddle valve?
Quote from the video:
Quote from Youtube video: The sample the settle melt like it's laid out here little rubber piece fits the channel of the pipe hug the pipe the the actual saddle valve is going to get inserted. Into the saddle. And twist.
