The preferred location is either the top of the door or on the side (either hinges-side or the opposite of). You will want to place the sensor so it is easier for you to wire it to the control panel.
Where do you put the contact sensor on a door?
Quote from the video:
Quote from Youtube video: If you're using your sensor to monitor a door place your sensor at the top of your door. This keeps it out of the way of kids pets and accidental bumps or kiss.
Where should contact sensors be?
Do cover your basement: A burglar will try any way they can find to enter your home, so don’t neglect your basement. A good placement in a basement is covering the staircase up to the main floor. Be sure to place the motion sensor properly so it covers the entire staircase.
Where do you install alarm door sensors?
Quote from the video:
Quote from Youtube video: Place the sensor towards the top of the door for best results always mount the sensor inside the home or building away from the elements.
How do you install a recessed door sensor?
To install the recessed door/window sensor:
Using an 3/4” drill bit, drill a 5/8” deep hole for the magnet. Mark the location directly across for the sensor hole, and then drill a 2 ¼” deep hole for the sensor. Push both magnet and sensor into mounting holes until they are flush against the frame.
How high up should you put a motion sensor?
Ideally, it’s best to mount motion sensing lights six to 10 feet above the ground and positioned so that most movement will occur across the sensitivity zone, rather than directly toward the detector.
How close do ring contact sensors need to be?
The space between the Contact Sensor and the Magnet is 1 inch or less. When you open the door or window, you see the LED flash green (and hear the chirp tone, if enabled). There needs to be ½ inch of space around the Sensor so you can slide it open to replace the batteries.
How do you install a vivint recessed door sensor?
Go to your recessed door sensor and use a penny or dime to twist the sensor to the left and out of the door frame. Take out the old battery and replace with a CR2 battery. Slide the sensor back into the door frame with the two guides lined up. Use your coin to twist the sensor to the right to tighten it into place.
How do you install Simplisafe entry sensor on door with molding?
Quote from the video:
Quote from Youtube video: Okay and the magnet goes on the side the mood non-moving part and the sensory item goes on the part that moves so I want to peel off your sticky side for both I must go set this up on the door shall.
How do you wire a door for a contact?
Quote from the video:
Quote from Youtube video: And then when this screw is tightened up the washer will clump down on to the actual conductor. Then we're going to repeat a process for the terminal and outside which will be the blue wire.
Where is the best mounting location for a motion detector?
We like to install motion detectors in areas that cover rooms as efficiently as possible. Specifically, we find that installing a detector in the corner of a room that faces the entrance provides the best coverage.
How high can a motion sensor light be?
Most motion sensors on exterior lights have a limit of 25′ for them to operate, so you don’t want to push that limit too aggressively. The higher up the lights are mounted the less distance they can view.
How many motion sensors do I need?
However, you don’t need countless motion sensors for your home’s security system to be effective. In fact, having too many motion sensors can render your security system useless. Since motion sensors tend to have the capability to monitor a large amount of area, one motion sensor per room is typically effective.
What height should a security light be?
around 6 to 10 feet
Motion sensor lights are usually best placed at around 6 to 10 feet (1.8 to 3 meters) above the ground and facing downwards. The higher the lights are placed, the wider the radius they will cover.
Can wind set off motion sensor light?
On its own, the wind won’t trigger the motion sensor of a security light. But it can cause something else to trigger the sensor, mainly if it detects motion through movement and you have tree branches or loose objects in view.
Can mice set off motion sensor?
Homeowners with pets should be certain the home security system has sensors that are “pet- friendly,” as pets that are free to roam the house will trigger motion detectors and activate a false alarm. Rodents and insects can also trigger alarms.
Does cold weather affect motion sensor lights?
Motion activated lights are often affected by hot and cold temperatures.
