It may be possible that the circuit is just too long, and the resistance in the conductors themselves are causing the imbalance. Try connecting the new receptacle to the previous receptacle temporarily, using short pigtails (CAUTION: Working on energized circuits is dangerous.).

Can another outlet cause a GFCI to trip?

The GFCI outlet works fine, while anything plugged into the other outlets causes the GFCI to trip.

Can I protect a more than one receptacle with a GFCI receptacle?





Single-location protection offers GFCI protection only at one receptacle. Multiple-location wiring protects the first GFCI receptacle and every receptacle downstream of it (including standard receptacles) in the same circuit.

How do you fix a GFCI outlet that keeps tripping?

If there’s water in the GFCI, trip the breaker and use a blow dryer to dry out the receptacle box. Once the outlet is completely dry, reset the GFCI. Unplug everything from the outlet and see if the GFCI stops tripping. Plug everything back in one at a time to see which appliance is causing the breaker to trip.

Can GFCI outlets be daisy chained?

Daisy chaining GFCIs does not increase protection. In industrial and commercial installations, GFCI devices may be daisy chained, but the upstream GFCI devices usually are set to a higher trip point while the downstream GFCI devices protecting point-of-use receptacles is set to the standard 6mA.

Can one outlet cause other outlets not to work?

Series Wires (Daisy Chaining)



Daisy-chaining electrical outlets means that each outlet is connected in a series. When they’re connected in a series, if one breaks down that means that the rest of the connected power outlets will no longer work either.

Is there a difference between GFI and GFCI?





Ground fault circuit interrupters (GFCI) and ground fault interrupters (GFI) are the exact same device under slightly different names. Though GFCI is more commonly used than GFI, the terms are interchangeable.

Can you have 2 GFCI outlets on the same line?

When you need to wire multiple GFCI outlets such as in a kitchen or bathroom you have a couple of options. To save money, you can put in a single GFCI and then wire additional standard outlets to the “LOAD” output from the single GFCI.

Can 2 GFCI receptacles be wired in series?

You only need 1 GFCI outlet per circuit (assuming it’s at the beginning of the line and the rest of the outlets are loads). They are correctly wired in parallel – if they were in series, you wouldn’t get the correct voltage at the other outlets when there is any type of load present.

How many outlets can one GFCI protect?

There’s no limit. A standard GFCI will protect up to 20 amps, drawn from any combination of receptacles, either the built-in one or any number of additional ones connected to its load terminals.

How many outlets can you daisy-chain off a GFCI outlet?



All GFCIs trip at a current leakage as low as 4 to 5 milliamps. There is no additional safety gained from daisy-chaining two or more GFCIs together. If your home has multiple GFCI outlets on the same circuit, and you trip a downstream GFCI, the lead GFCI will also trip.

Can you plug a GFCI into a GFCI outlet?

A GFCI protected machine should work with any GFCI outlet, are you sure the machine is GFCI protected, Some types of systems have large leakage currents and they will trip a GFCI every time the motor cycles up and down due to the harmonics generated (leakage).

Can a GFCI be in the middle of a circuit?

Now, start your GFCI wiring by connecting all black “hot” wires to each other with one going to the GFCI. What is this? If your outlet is in the middle of your circuit (meaning, other outlets or switches are wired through it), you may have two black wires coming out of the wall.

What would cause two electrical outlets to stop working?



Your Circuit Breaker Tripped



If your outlet has short circuited or been overloaded, then your circuit breaker may have shut off its power. Check other nearby outlets to see if they are working. If they also are dead, then go to your circuit breaker.

What causes multiple outlets to stop working?

An Overloaded Circuit. This is a common occurrence. The electricity demanded from the breaker could be too much for it to handle causing it to trip. When a circuit breaker trips, it shuts off the power being supplied to that area of the house.

How do I know if my outlets are daisy chained?

Most electricians wire electrical receptacles in this daisy-chain series. Ground connections on daisy-chained receptacles: Notice that only the hot and neutral wires are daisy-chained through the receptacle’s screws and copper strap.

Is it better to pigtail outlets?

Use Pigtails on Outlets



Outlets have pairs of screws on each side that you can use to connect downstream outlets, but it’s best not to use them. There are two reasons for this. First, connecting the wires leading to downstream outlets with wire connectors creates a more secure connection.

How do you piggyback an electrical outlet?



Quote from the video:
Quote from Youtube video: The wires from the new cable onto the old along with pigtails that will connect to the new device once connected fasten the receptacle.

How many outlets can you add to an existing circuit?

(Don’t make matters worse by adding yet another outlet to the circuit.) Electrical codes restrict the number of lights or electrical outlets that can be connected to one circuit. Typically, you can have no more than eight lights or electrical outlets on a 15-amp circuit.

Can I piggyback an outlet from another outlet?

Answer: Absolutely you can. Using 12-3 wire (for a 20 amp circuit, or 14-3 wire for a 15 amp circuit) splice the new wire to both wires on the “hot” side of the outlet and to the white wire. You may need to cut 6″ pieces of wire to go from each wire nut to the outlet. Splice the ground to the existing ground as well.

How do you daisy chain an outlet?

To daisy-chain a receptacle onto one that already has power, you attach the black and white wires to the remaining pair of terminals, black to brass and white to chrome. You then twist or crimp the ground wires and attach one of them to the ground screw.