Why does my washing machine have water under the drum?
Fortunately, there is usually a simple explanation for water leftover in a washing machine. A washer drum full of water generally indicates that: Your Drain Hose is Clogged OR. Your Washing Machine Pump is Broken.
Why is my GE washer not fully draining?
A kink or clog in your washing machine’s drain hose could be interfering with water flow and preventing your machine from draining properly. To inspect the drain hose, turn off the power to the washer, disconnect the hose (have a bucket ready to catch any water), and check the hose for damage or obstructions.
Where is the drain filter on a GE top load washer?
Top Load Washer – Lint / Pump Filters
- There are 2 crescent-shaped Fine Mesh plastic lint filters in the bottom of the wash basket under the agitator. …
- During drain down and spin, the water forces the lint off the bottom of the filters and down the drain.
- These filters should never require cleaning or replacement.
How do I get water out of the bottom of my washing machine?
Quote from the video:
Quote from Youtube video: And once you get once you get close to the bottom it's still too heavy. You can use a gallon bottle. Kind of lay it down. Get this hose real low water is going to keep coming. Out.
How do you drain a GE top load washer?
Here’s how to do it.
- TURN OFF THE POWER. Unplug the washing machine from the power outlet.
- REMOVE LAUNDRY. Take out any clothing that’s in the washer tub.
- EMPTY THE TUB. Use a bucket to scoop the water out of the washer tub. …
- MOVE WASHER AWAY FROM THE WALL. …
- DISCONNECT DRAIN HOSE. …
- PINPOINT THE ISSUE.
What happens if water stays in washing machine?
What to Do When Your Washing Machine Won’t Drain
- Perform a Master Reset. Unplug your washer for about one minute. …
- Test the Lid Switch Assembly. …
- See if the Drain Hose is Kinked. …
- Check the Drain Hose or Pump for Clogs. …
- Clean out the Coin Trap. …
- Check the Water Level Control. …
- Schedule Washing Machine Repair.
How do you test a GE washing machine drain pump?
Quote from the video:
Quote from Youtube video: I set my meter to volts EC turn the washer to the drain spin cycle that way when you start the first thing that's going to happen it's going to try to drain.
Where is the coin trap on a top loading GE washer?
Refer to your user manual to determine the location of your washer’s coin trap or pump filter. Most are located behind a small door on the front right corner of the machine. Open the door, and twist the filter to remove it.
How do I get my GE washer to drain and spin?
If the washer is running, press the “Start/Pause” pad once to interrupt the cycle, then select “Drain and Spin” and press the “Start/Pause” pad again. If the “Stop” pad has been selected and the washer is still full of water, select “Drain and Spin” and then press “Start”.
How do you get water out of a top loading washing machine?
How to Manually Drain a Top-Loading Washing Machine
- Step 1: Turn off the power and lay down towels. …
- Step 2: Locate the drain hose at the back of the washing machine. …
- Step 3: Drain the water. …
- Step 1: Turn off the power and lay down towels. …
- Step 2: Locate the drain hose. …
- Step 3: Drain the water. …
- Step 4: Scrub the filter.
Is there supposed to be water in the bottom of my washing machine?
It is supposed to have water underneath the drum; it is only an issue if it backs up into the drum. That water gets changed every time you run the machine. It might be the rubber lining that smells and not the water below the drum.
Why won’t my GE washer drain and spin?
When a load is properly balanced but still won’t spin, there may be an issue that prevents the water from draining from the machine. Make sure the drain hose is properly connected and that there are no kinks or pinched areas. Your washer may not drain and enter the spin cycle if the pump filter is clogged.
Why is my GE top load washer not spinning?
If you are facing GE washer not spinning problem, first try closing and opening the lid — if that doesn’t work, check to see if the lid switch itself is broken. If your GE washer won’t spin, check to make sure the lid switch is being activated mechanically.
Why are my clothes too wet after the spin cycle?
Loading Too Many Items
Overloading can lead to an imbalance that reduces the washer’s spin speed, leaving clothes too wet after spin cycle completes. If the washer leaves clothes soaked after a large load, remove some items, redistribute others and run another rinse and spin cycle.
Why is my washer not spinning all the water out of my clothes?
The most likely culprit for a washer that spins but still turns out soaked clothing is a drain hose problem. It could be clogged, kinked, or even positioned incorrectly if you had to remove the drain tube to make another repair already.
How do you reset a GE washer?
Unplug the washer for one minute, then plug the washer back into the electrical outlet and lift and lower the lid six times within 12 seconds. This will reset the motor and you should be able to start the cycle.
How do you unclog a washing machine drain hose?
Quote from the video:
Quote from Youtube video: The drain pump simply undo the clamp. And pull the hose off of the open that port or the public which is a small port.
How do I know if my drain pump is clogged?
Quote from the video:
Quote from Youtube video: If the noises are happening during the drainage. Then that could be an issue with the drainage pump. If you've checked all of these areas for blockages.
Can I use Drano to unclog my washing machine drain?
Yes. Drano or any drain cleaner can be used to unclog your washing machine drain, but make sure you run your washer without a load of laundry before normal use.
