If your air filter is dirty it would prevent enough air flow across the heat exchanger to keep it from over heating causing the roll out safety switch to open. If this is neglected for a long period of time it can cause the ROS to weaken and begin to trip at lower than designed temperature.

Why does my Goodman furnace keep shutting off?

Quote from the video:
Quote from Youtube video: But then it turns itself off right away most likely you've got a flame sensor that's dirty.

Why does my furnace start up and then shut off?

Having a dirty air filter in your furnace can cause short cycling. While a faulty flame sensor will lead to an immediate shut-off, a dirty filter will allow your furnace to run for several minutes and then shut down. You might notice that the air being pumped out of the heat grates is significantly hotter than normal.

Why is my furnace not staying on long enough?

If your furnace keeps shutting off, it could be due to low airflow. There are several indirect issues that cause low airflow. Dirty Air Filters. If you don’t change your air filters often enough, the filters will become dirty and clogged, which means the heat exchanger retains heat and eventually causes it to overheat.

Why does my furnace turn off after a few minutes?

If your furnace shuts down after a few minutes, it’s likely due to a faulty or unhygienic flame sensor. This crucial component intends to monitor the gas burner. Also, when a flame sensor cannot detect the burner, the furnace runs for a few moments before shutting down and restarting.

Why is my Goodman furnace short cycling?

Reasons for furnace short cycling are: A bad flame sensor (flame rod) A very dirty furnace filter. Blocked heat grates.

How do you fix a short cycle on a furnace?

A dirty air filter is the most common cause of short-cycling. If your air filter is clogged with dirt, it won’t allow proper air flow to the heat exchanger. That can cause the furnace to overheat and forces the high limit switch to ride to the rescue by shutting the furnace off.

How do you clean the ignition sensor on a furnace?

Quote from the video:
Quote from Youtube video: So if you have a situation like this what you have 90% of the time is just a dirty flame sensor. So we'll go through the steps on how to clean it. So the right side of the furnace.

Can a bad thermostat cause a furnace to short cycle?

Thermostat Troubles Can Cause Short Cycling



Your furnace or central air conditioner spends a good amount of energy simply turning on and off, which is why you want yours to run for at least 15 minutes at a time before shutting off.

Does a Goodman furnace have a reset button?

The exact location of the reset button will vary by model on each Goodman furnace. However, you will need to open up the front panel of the furnace to access it. In many furnaces, the switch will be located in the air handlers compartment next to the blower motor (it will typically be a yellow or red button).

How do you fix short cycling?

How To Stop and Prevent Short-Cycling

  1. Check your air filter. Believe it or not, a clogged air filter can cause a wide variety of air conditioning issues. …
  2. Check your thermostat placement. …
  3. Check your air conditioner’s refrigerant levels. …
  4. Replace the low-pressure control switch. …
  5. Check the compressor.


Is short cycling normal?

One of the most common, and unfortunately harmful, problems an air conditioner can have is something called short-cycling. This is both a symptom of a problem and a cause of a problem. Sometimes a few simple adjustments may be all that’s needed to repair the issue.

What is considered short cycling?

Short cycling has nothing to do with time between normal on-off cycles. Short cycle occurs when unit is rapidly turned off then back on within less than 3 minutes at t-stat or power interruptions such as during lightning storms.

How do you know a thermostat is bad?

7 Ways to Tell Your Thermostat Is Broken

  1. Thermostat Has No Power. …
  2. AC or Furnace Won’t Turn On. …
  3. Heater or AC Won’t Turn Off. …
  4. Thermostat Doesn’t Match Room Temperature. …
  5. Thermostat Doesn’t Respond. …
  6. Short Cycling. …
  7. Thermostat Forgets Programmed Settings. …
  8. Thermostat Replacement Services.


How do I know if I need a new thermostat?

Signs You Need a New Thermostat

  1. Heating or cooling system will not turn off or on.
  2. The temperature reading is incorrect.
  3. Recent spike in your energy bill.
  4. Frequent temperature fluctuations.
  5. Thermostat is 10 years old or older.


What does it mean when a furnace is short cycling?

Short cycling is when the furnace turns on for a short period of time but then turns off. This start-and-stop cycle can keep your home from properly warming up and may also damage your furnace itself.