Yes, if you bond the layers of plywood together as a single structure using construction adhesive.

Can I put cement board over plywood?

If you’re working over a wood subfloor, cement board is the right choice for your tile base. No matter what you’re told at a home center, it’s not a good idea to install tile directly over plywood, especially in a damp area like a bathroom.

How thick should plywood be under tile?

The subfloor under the tile should be at least 1 1/8″ thick, with a minimum of 5/8″ thick exterior grade plywood topped by 1/2″ cement backer board.

Can you put backer board over plywood?

Quote from the video:
Quote from Youtube video: And then put it down and in a older board or screwed it down it would have caused a lot of problems pulling the plywood up the thinset would have wanted to pull the plywood up. And then I'm running

Can you tile 1/2 plywood?

Tile can be laid on plywood. But do not install tile directly on the plywood subfloor itself. Use an intervening layer of a sheet of thinner plywood.

How do you install cement board on plywood?

How to Install a Cement Backer Board Over a Plywood Subfloor in the Bathroom

  1. Dry-Lay the Floor. Lay down full sheets of backer board where they will fit first. …
  2. Take Your Measurements. …
  3. Make Your Cuts. …
  4. Use a Keyhole Saw. …
  5. Mix Your Thinset Mortar. …
  6. Apply the Thinset. …
  7. Nail the Concrete Board Down. …
  8. Repeat to Cover the Floor.

Can you lay tile over plywood subfloor?

While you can lay tile directly over a concrete slab using thin-set adhesive, don’t make the mistake of applying tile directly to a plywood subfloor. No matter how firm the subfloor; the plywood will expand and contract at a different rate as the tile, causing cracks to develop in the grout lines or tiles over time.

What kind of plywood do you use for subfloor under tile?

Exterior-Grade Plywood

Exterior-Grade Plywood



Exterior plywood is an acceptable underlayment for tile and is preferred to interior-grade plywoods because the bonding adhesives used are waterproof. If water seeps through the tile installation to the underlayment, it will not cause the wood to swell, as happens with interior-grade plywood.

What do you put on subfloor before tile?

Quote from the video:
Quote from Youtube video: Once you've prepared your wood subfloor you will need to install cement.

What thickness plywood should I use for bathroom flooring?

Make Sure Your Subfloor is Structurally Stable



The installation guide for 1/4 inch HardieBacker recommends having wood subfloors made of 5/8 inch exterior grade plywood or OSB (oriented strand board) that is 23/32 inches thick.

Can you tile directly onto plywood?

Under British Standards BS 5385 Part 1, plywood is not a suitable substrate for the direct fixing of wall tiles, therefore when tiling onto walls, a tile backer board is required.

What do I need to lay tile on plywood?

Quote from the video:
Quote from Youtube video: The tile industry recommends a subfloor that's at least an inch and a quarter thick.

Can you use 1/4 inch cement board on floors?

1/4″ USG Durock® cement board is an ideal substrate for floor and countertop ceramic tile installations. The 1/4″ thickness helps eliminate transition trim when abutting carpet or wood flooring and minimize level variations with other finish materials.

Do you have to put thinset between subfloor and cement board?

Not only is thinset a critical component underneath cement board but the other critical component is the fasteners. And you won’t have the fasteners if you are trying to install it over concrete.

Can I just screw down cement board?

Doing this will require that you remove the existing surface material before installing backer board over the studs. Cement board can also be used on countertops when laying tile. However, the process will involve using an extra sheet of backer board. Never use standard screws when installing cement board.

How do you attach cement board to wood subfloor?

Quote from the video:
Quote from Youtube video: And what you want to do is about every 12 inches. You've got to be a rule around proximately. Every 12 inches. You want to glue to the subfloor where it's going to be applying cement. Word.

Can I screw cement board to subfloor?

Cement board can be installed over a plywood subfloor using an appropriate construction adhesive and screws for a quicker project that’s less messy than taping and mudding.

How thick should backer board be for tile floor?

Cement-fiber, or similarly reinforced, backer board comes in standard 1/4 inch and 1/2 inch thicknesses. If you’re installing backer board over an existing subfloor, 1/4 inch is sufficient. If you’re installing backer board in new construction, attaching it directly to floor joists, opt for 1/2 inch sheets.

Do you have to tape cement board before tiling floor?

Yes. And use the alkali-resistant CBU tape. One tip, which might help or hurt – when you tape ahead of time and let the thinset dry before tiling you can get some bumps among the tape and thinset.

Should you tape cement board joints?

Quote from the video:
Quote from Youtube video: I recommend that you get cement or tape mainly because it sticks to cement board better.

How do you waterproof cement board before tiling?

Quote from the video:
Quote from Youtube video: Number 30 felt paper or house wrap is a fail-safe drainage plane for behind the backer board. Make sure to overlap the felt to direct water into the tub not into the wall.