Did you mean:

What size wire do I need to run 100 amp service?

Installation of 100 amp electric service or subpanel needs a #4 AWG copper wire or #2 AWG aluminum or copper-clad wire inside a minimum 1.25 inch, schedule 40 or 80 PVC electric conduit for underground service.

What size wire do I need to run to my shop?





The minimum wire size for a 30-amp, 240-volt circuit is 10-gauge, but to prevent poor performance because of voltage drop, you should consider upgrading to 8-gauge if the outlet is far from the panel. For a 50-amp circuit, you need a 6-gauge wire at a minimum.

What size wire do I need for a 100 amp underground 150 ft run?

Quote from the video:
Quote from Youtube video: What size wire do i need to run 100 amp service 150. Feet what is the right wire size for 100 amp service 150 feet distance you should get two over zero awg copper wire or four over zero awg aluminum

What kind of wire do I need for a detached garage?

So, that said, I’d use 2AWG, wet-location-rated (THWN or XHHW-2) aluminum wire for both hots and the neutral with an 8AWG or 6AWG (8AWG works, 6AWG might be more useful for grounding electrode conductors though) bare copper ground wire. That will give you 70A at the garage without coming close to filling a 2″ conduit.

What wire size do I need to go 100 feet for a 100 amp service to a workshop?

For a 100 ampere circuit, the conductors will likely be required to be 3 AWG copper or 1 AWG aluminum.

What size wire do I need to run 100 Amp Service 100 feet?





If you check the wire size chart (you have the link in the introduction), the #0 AWG wire (also known as 1/0 AWG wire) has 150 ampacity. That means that #0 AWG wire is the perfect size wire for 100 amp service 100 feet away.

What size wire do I need to run a 100 amp subpanel?

The cable must have a wire gauge sufficient to the amperage of the subpanel—a 100-amp subpanel requires #4 copper wires or, more commonly, #2 aluminum wires, for example. (Aluminum is often used for feeder cables because the cost is typically much lower than that of copper wires.)

What size wire do I need for a 100 amp underground 300 ft run?

for 300 feet for 100 amp rated service I would use Aluminum direct burial 1/0-1/0-1/0-1/0, the forth can be as low as #4 for the ground (but also in conduit, even if in conduit must still be rated underground wire and required by code also) Also note the size wire the breaker can handle, cannot cut strands to make fit, …

How many amps is #6 wire good for?

Size & AMP Ratings

NM, TW, & UF WIRE (Copper Conductor) SE CABLE (Copper Conductor)
12 AWG – 20 AMPS 6 AWG – 65 AMPS
10 AWG – 30 AMPS 4 AWG – 85 AMPS
8 AWG – 40 AMPS 2 AWG – 115 AMPS
6 AWG – 55 AMPS 1 AWG – 130 AMPS

What wire size do I need to go 100 feet for a 60 amp service to a workshop?



What size wire should I use for a 60 amp subpanel? You can get away with 6 AWG when you have a short run of wire, however, due to voltage drop, if you ever decide you want to go more than 100 feet then a 4 AWG is the size you should choose.

How far can you run 10 gauge wire for 30 amps?

How far can you run 10 gauge wire for 30 amps? 10-gauge wire is usually used for short 30 amp runs. If you plan on going over 150 feet, 8-gauge wire or thicker will be needed.

How many amps is #8 wire good for?

#8 Gauge THHN Copper Stranded Wire is the most popular single conductor copper wire we carry and is RATED FOR 55 AMPS @ 90°C.

Will 8 AWG carry 50 amps?



A copper conductor’s conductivity is affected by temperature. Up to a point, the higher the temperature, the higher the current the wire can handle. An 8-gauge wire can handle a current of 50 amps at a temperature of 90-Celsius or 194-Fahrenheit.

How many amps is #10 wire good for?

30 amps

RULES OF THUMB



“Twelve-gauge wire is good for 20 amps, 10-gauge wire is good for 30 amps, 8-gauge is good for 40 amps, and 6-gauge is good for 55 amps,” and “The circuit breaker or fuse is always sized to protect the conductor [wire].”

What is 8 AWG wire used for?

This wire is 8 AWG, good for 55 Amp when used in conduit with less than 3 conductors. This wire is rated for use in dry or wet locations, raceways, or conduit. It can be used outside exposed to the weather as well, though the insulation is not 100% UV-proof and installation in conduit is recommended.

How do I choose wire gauge?



To determine what gauge wire you need, consider the carrying capacity and the amount of current the wire needs to conduct (measured in amperage or amps). Wire gauge is directly related to how many amps you need to run through it. The distance you need the wire to go can also impact the gauge of wire you need.

What is 10 AWG wire used for?

10-gauge are used in electric clothes dryers, 240-volt window air conditioners, electric water heaters supporting 30 amps. 6-gauge are used for cook tops and ranges carrying 40-50 amps. 4-gauge are used for electric furnaces and large electric heaters protected at 60 amps.