How do you install recessed lighting over joists?
Quote from the video:
Quote from Youtube video: So all you have to do is wire this one up just like we've wired up the rest of them and we're good to go so always make sure that the can lights which are using or matching.
How do you wire recessed lighting in existing ceiling?
Quote from the video:
Quote from Youtube video: So you cut it out then you drill your holes through the joist just like i'm going to drill my holes through these studs. And then you run your wire. Across.
What wiring do I need for recessed lighting?
Typically, a 12-gauge cable with two insulated conductor wires and a ground wire are used. The cable is jacketed with a non-metallic plastic jacket to protect it.
Should recessed lights be wired in series or parallel?
parallel
Wiring in series reduces the voltage of each light. For example, if you have four lights rated for 12 volts, they will need to be wired in parallel to receive the full 12 volts. But, if you have four lights rated for 3 volts, you can wire them in series and connect them to a 12-volt source.
How do you run a wire through the ceiling without an attic?
Quote from the video:
Quote from Youtube video: That's good if you want to run wires. Because then you have access all over the place. So basically you're recessed cans are your ceiling joists are going to run back and forth.
How can I install recessed lights without attic access?
Quote from the video:
Quote from Youtube video: I would go in and make a hole at the top of the wall. Make a hole in the ceiling. And that would allow me to get into this bay. And then to grab the wiring.
Can you put recessed lights in an existing ceiling?
Recessed lighting is easiest to install during new construction, but can be retrofitted into existing ceilings. Because recessed lighting is installed in the ceiling, it’s simplest to put in during new construction or a major renovation, before ceiling material goes up.
How many recessed lights can I put on one switch?
The main limitation on the number of recessed lights that a single switch can control is the rating of the circuit breaker controlling the circuit. Each incandescent or halogen 60-watt bulb draws around 1/2 amp, and therefore, standard lighting with a 15amp breaker can manage 30 lights.
What is the difference between can lights and recessed lights?
Recessed lights, also known as can lights, are described as metal light housings installed in the ceiling for a sleek look that gives you back your ceiling. Their diameter generally varies from 3” to 6.”
Can I daisy chain recessed lights?
Remember that you must run one ultra-thin extension cable (or run of low voltage wire) for each light. You can not daisy chain multiple lights together.
How do you wire multiple recessed lights?
Quote from the video:
Quote from Youtube video: Go ahead and take the switch off unscrew. It cut the cables strip them now grab your dimmer switch wire not your connectors and Grahm the greens to the box put it all together and give it a test.
How many LED recessed lights on a circuit?
The limit is 12, unless you are installing devices that have a known load. In the case of a LED light which is hardwired in, or a smoke alarm, you can put as many of these devices on the circuit providing you don’t exceed the 80% load.
Can you run electrical wire through floor joists?
You can safely drill joists for electrical and plumbing runs without weakening the joists, if you follow the rules. By the DIY experts of The Family Handyman Magazine. Where and how to drill joists for electrical cables or plumbing runs depends on what type of floor framing you have. Keep the hole at least 2 in.
How do you run electrical wire through ceiling joists?
The best way to run wires along ceiling joists is to use a running board, spacing the wires evenly with electrical staples. This is for running wires in the direction of the joists or perpendicular to them. If there is no space, you can bore holes in very specific places to run wires through.
Can you run Romex on top of ceiling joists?
There is nothing wrong with running your electric on top of joists but you really should try to do it in areas that aren’t going to be exposed to any foot traffic. If you need to go parallel then simply run them a few inches down on the side of a joist.
Can you staple Romex to bottom of joists?
It is okay to staple Romex along the floor joists, provided you keep it at a safe distance from the edge. This will help you protect it from screws and nails and any critters that may be crawling along the edges – since that is where insects usually decide to burrow. You can also run Romex THORUGH floor joists.
Can you run two wires through the same hole?
The Answer
According to the National Electrical Code, you can have 4 12/2 nonmetallic sheathed cables through a single bored hole that is fire- or draft-stopped using thermal insulation, caulk, or sealing foam, or where proper spacing is not maintained for more that 24 in.
What is the code for strapping Romex?
Romex Wiring Support, NEC 336-18: Stapled, in a manner that does not damagethe cable, within 12″ of electric boxes; every 4-1/2 ft. intervals, and clamped to box. Cables run through holes in studs, rafters of floor joists are considered supported at those points.
How far apart should Romex be stapled?
The clamps, staples, or braces holding a Romex cable shouldn’t be any further than 4.5 feet. However, we recommend stapling after every 2 feet, just to be sure. This is especially true when running a wire where you won’t have immediate access all the time.
How far apart do you support Romex?
Article 336-18 stated that cable must be secured in place at intervals not exceeding 4.5 feet (1.37 m) and within 12 inches (305 mm) from every cabinet, box, or fitting.
