Can you use recessed light as junction box?
3 Answers. Show activity on this post. Modern recessed lights have junction boxes built in. You are free to daisy-chain other lights or receptacles, so long as you connect properly and do not exceed the number of wires for the size of the built in box.
What is the minimum distance between light and wall?
If you plan to illuminate an entire wall or accent particular architectural features or pieces of art, the rule of thumb is to place your recessed light fixtures between 1.5 feet and 3 feet from the wall. If your fixtures are fixed, they should be placed a bit closer to the wall.
What is the rule of thumb for recessed lighting?
A good general rule for placement is to divide the height of the ceiling by two. The result is the amount of space to leave between each light. For example, recessed lighting spacing for an 8-foot-high ceiling would be 4 feet between each light. This will provide good spacing for general room lighting.
How do you install a recessed lighting junction box?
Quote from the video:
Quote from Youtube video: Definitely easier there it is make sure each wire has at least 12 to 18 inches of slack. At each opening insert the wires into the junction box and use wire nuts to make the connections.
What is a recessed junction box?
A recessed box is a plastic compartment through which the cable wires exit. A socket or switch is mounted to the front. As the name refers to, the recessed boxes are built into the walls.
Should you stagger recessed lights?
The typical rule is to place the lights the same number of feet apart as the bulb’s diameter in inches. So a bulb with a 4-inch diameter should be 4 feet away from the next light.
How far apart should 4 inch recessed lights be?
Generally speaking, recessed lights that are four inches in size should be placed four feet apart. Six-inch lights should be placed six feet apart. In other words, the diameter of the lights equals the space between them.
How far should recessed lights be from wall in kitchen?
24 inches
The best recessed-light location is 24 inches from the wall, directly above the countertop edge. Light levels dropped dramatically when the cans were located farther away.
How do I run a wire for recessed lighting without attic access?
Quote from the video:
Quote from Youtube video: Come up through the hole feed the wire. In through that first can light opening. Pull it down with my fish tape. And then pull it out on the first opening there at the top of the wall.
How do you install a junction box?
Instructions
- Mount the Box. Separate the circuit wires at the existing splice and loosen the cables as needed to make room for the new junction box. …
- Set up Clamps for Each Cable. Install a cable clamp for each cable, as needed. …
- Secure the Cables. …
- Join the Wires. …
- Finish the Job.
How many wires can be in a recessed light box?
National Electrical Code NEC 314.16 and Box Fill
Specifically, the documentation states that the light fixture electrical junction box may accommodate up to eight 12 gauge copper wires.
Should recessed lights be wired in series or parallel?
You can wire them in any sequence. Do it in whatever way is the most convenient. The electricity doesn’t care, and doesn’t know the physical location of the fixtures. Household wiring is parallel, so there isn’t really a sequence.
How do you can daisy-chain recessed lighting?
In the attic, run a wire from over the switch location to the first six-inch light, then to the next and so on until all six-inch lights are daisy-chained to the switch location. Daisy chain the two small lights back to the same location using a separate set of wires.
How many recessed lights can I put on one switch?
The main limitation on the number of recessed lights that a single switch can control is the rating of the circuit breaker controlling the circuit. Each incandescent or halogen 60-watt bulb draws around 1/2 amp, and therefore, standard lighting with a 15amp breaker can manage 30 lights.
Can I daisy chain LED recessed lights?
Remember that you must run one ultra-thin extension cable (or run of low voltage wire) for each light. You can not daisy chain multiple lights together.
How do you wire multiple recessed lights to one switch?
Quote from the video:
Quote from Youtube video: Go ahead and take the switch off unscrew. It cut the cables strip them now grab your dimmer switch wire not your connectors and Grahm the greens to the box put it all together and give it a test.
How many LED lights can be on a 20 amp circuit?
Maximum Lights Per Circuit
Technically, you can install 13 outlets or lights on a 20-amp CB, but you can only put ten lights per circuit due to the 80% rule of maximum continuous load.
How far can you run 12 gauge wire on a 20 amp circuit?
After these distances, the circuit will go over the recommended 3% voltage drop. You can run a 12 gauge wire up to 70 feet on a 15 amp circuit. That number drops to 50 feet if you run 12 gauge wire on a 20 amp circuit.
Can you run lights and outlets on the same circuit?
Yes, you can. The average home uses an indoor distribution board that houses the breakers of the majority of circuits in the home. A circuit controlled by a 15A circuit breaker (which a lot of contractors use for general lighting) can also accommodate outlets.
